manualshive.com logo in svg

Sakura Tissue-Tek TEC 6, Operating Manua

Share
Download
Sakura Tissue-Tek TEC 6 Operating Manua Download Page 10

10

WARNINGS:
•  Follow instructions in this operating manual.
 

If the instrument is not used properly, it may induce failure of the 

instrument, injury to operators, and/or damages to facilities. 

•  Do not put flammable/explosive substances other than paraffin in the 

instrument.

 

When using the instrument, do not put flammable/explosive 

substances other than paraffin in the areas where paraffin is intended 

such as the paraffin chamber and warming chamber. Doing so may 

result in fire or explosion.

•  Do not move the instrument while molten paraffin is inside.
 

Do not move the instrument while molten paraffin is inside. Before 

moving the instrument, unplug the power cord and remove the paraffin 

inside the instrument or wait for it to cool and solidify. Failure to 

follow this instruction may result in the paraffin spilling over to cause 

burns or contacting with live electrical parts to cause fire.

•  The instrument, paraffin and paraffin container become hot.
 

The paraffin melting part, paraffin and paraffin container in the 

instrument become hot. Exercise caution to prevent burns. 

•  Do not disassemble or modify the instrument.
 

Do not disassemble or modify the instrument except for the areas 

specified in this manual. The instrument may malfunction or cause 

accident, thus creating a dangerous situation.

•  Do not wet the instrument.
 

Do not wet the instrument except for the areas specified in this 

manual. If the instrument gets wet, electrical current leak may occur 

and cause fire or electric shock.

•  Do not operate the switches with a wet hand.
 

Failure to observe the instruction may result in electric shock.

•  Do not connect/remove the power plug with a wet hand.
 

Failure to observe the instruction may result in electric shock.

•  When connecting/removing the power plug, do so by holding the 

plug.

 

Connecting/removing the power plug by holding parts other than the 

plug may cause fire or electric shock.

•  Do not damage the power cord.
 

Do not forcibly bend, pull, twist or bundle the power cord. If the 

damaged power cord is used, fire or electric shock may occur. If 

the power cord or power plug has scratches or other abnormalities, 

contact the Sakura instrument distributor or representative.

Summary of Contents for Tissue-Tek TEC 6









































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands