Sakai SV510-III Shop Manual Download Page 121

Page: 121 / 248

6-032

VIBRATORY DRUM • REAR AXLE

22) Install lifting bolts (M20) to axle shaft subassembly (35).

23) Apply grease to entire periphery of O-ring (36).

Install O-ring (36) on axle shaft subassembly (35).

24) Lift axle shaft subassembly (35) with a crane and lower it

slowly.

Supporting eccentric shaft subassembly (5) with a pipe or

the like, align center of vibrator bearing inner race to that
of shaft.

(35) Axle shaft subassembly : 240 kg (529 lbs.)

(NOTICE)

Install the axle shaft taking care not to tilt the vibrator
bearing.
When installing the axle shaft, take care not to allow

the O-ring to protrude from the fitting groove.

•

SV510-

-06077

Lifting bolt

SV510-

-06077

Lifting bolt

SV510-

-06078

SV510-

-06078

SV510-

-06079

Pipe

SV510-

-06079

Pipe

Summary of Contents for SV510-III

























































































































































































































































Search results

Summary of Contents for SV510-III

Reviews:

Related manuals for SV510-III

Brands by name

Popular brands

Sakai SV510-III, Shop Manual

Search results

Summary of Contents for SV510-III

Reviews:

Related manuals for SV510-III

Brands by name

Popular brands