Sakai CR271 Shop Manual Download Page 163

Page: 163 / 170

10-020

TROUBLESHOOTING

2-4. Vibration

Check following items before troubleshooting.

•

No blown fuses and power is applied up to fuses.

•

Throttle lever must be “FULL”.

2-4-1. No vibration occurs

Reference Fig.: 2-2-1

Check point

Check/Cause

Action

1. Vibrator Solenoid

•

Disconnect harness and measure resistance of coil.

Standard resistance : 4.7 Ω

•

If resistance is abnormal, vibrator solenoid is faulty.

Replace vibrator

solenoid.

2. F-R Lever Vibration

Switch

(1) When starter switch is ON, measure voltage between

F-R lever vibration switch terminal wire marked

VIB-SW1-1

and chassis ground.

Standard voltage : 12 V or more

(2) When starter switch is ON and F-R lever vibration

switch is pressed once, measure voltage between F-R
lever vibration switch terminal wire marked

VIB-SW1-2

and chassis ground.

Standard voltage : 12 V or more

•

If above item (1) is OK and item (2) is NG, F-R lever

vibration switch is faulty.

Replace F-R lever

vibration switch.

3. Harness Connecting

Between Terminal

•

Measure resistance of harness connecting between

terminals.

Standard resistance : 10 Ω or less

•

If resistance is abnormal, harness is faulty.

Repair or replace

harness.

Summary of Contents for CR271











































































































































































Search results

Summary of Contents for CR271

Reviews:

Related manuals for CR271

Brands by name

Popular brands

Sakai CR271, Shop Manual

Search results

Summary of Contents for CR271

Reviews:

Related manuals for CR271

Brands by name

Popular brands