Sakai CR271 Shop Manual Download Page 149 | Manualshive

Page: 149 / 170

background image

10-007

TROUBLESHOOTING

GW750-2-10002

Connector

Wire

Test probe

Needle

Lead cable

Equipment B

Test harness

Equipment A

1

2

3

Measurement using a test harness

Measurement from the backside of connector

Measurement on a lead cable

Measurement method
For measurement of voltage, connect the tester probes in parallel to the portion to be measured. Because
the voltage can be measured only when the connector is connected in position, contact the tester probes to
the terminals without disconnecting the connector. The following methods are available:

•

Measurement using a test harness
Prepare the test harness for the measurement.

•

Measurement from the backside of connector
Insert a wire from the backside of the connector.

•

Measurement on a lead cable
Remove the bundling tape from the harness to separate each cable, and stick the needle into the
relevant cable.

(NOTICE)

•

Except for preparing the test harness, proper protection must be made after the measurement to
prevent corrosion in the connector terminals or harnesses.

«
...
147
148
149
150
151
...
»

Summary of Contents for CR271











































































































































































Reviews:

No comments

Related manuals for CR271

Brand: ZAMST Pages: 21

Brand: 1010music Pages: 2

Brand: 1010music Pages: 4

Brand: Rain-Flo Irrigation Pages: 20

PELTOR WS LiteCom Plus

Brand: 3M Pages: 7

Brand: M-system Pages: 2

Brand: Rico Pages: 34

Brand: IDEAL Networks Pages: 60

Brand: IceCure Pages: 104

Brand: Pari Pages: 12

Brand: laerdal Pages: 2

Brand: laerdal Pages: 104

Brand: laerdal Pages: 33

Brand: Lafayette Pages: 2

Brand: Magma Pages: 16

Brand: Tadano Pages: 16

Brand: Strapack Pages: 16

Brand: Hameg Pages: 60

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands