Sakai CR271 Shop Manual Download Page 130

Page: 130 / 170

9-004

INSPECTION AND ADJUSTMENT

3. MEASUREMENT AND INSPECTION OF PROPULSION

CHARGE CIRCUIT PRESSURE

• Since oil in charge circuit is supplied from steering

circuit, confirm that steering operation is normal before
measurement.

3-1. Measurement

• Oil temperature during measurement : 50

± 5

°C (122

± 9

°F)

①

Remove plug from propulsion pump charge pressure
gauge port (1-8). Attach pressure gauge with adapter

ⓨ

• Adapter for

ⓨ

: 7/16-20UNF

• Pressure gauge : 0 to 5 MPa (0 to 725 psi)

②

Apply brake by parking brake lever.

③

Start the engine and set throttle lever to “FUll”.

• Then, read pressure indicated by pressure gauge.

★

Standard charge relief valve setting

: 0.5 MPa (72.5 psi)

• The number “1-8” appearing in above illustrations is consistent with lead line numbers shown in illustration of

propulsion pump in “2-2. Hydraulic Component Specifications” (page 4-006).

CR271-09003

1-8

PG001011

Summary of Contents for CR271











































































































































































Search results

Summary of Contents for CR271

Reviews:

Related manuals for CR271

Brands by name

Popular brands

Sakai CR271, Shop Manual

Search results

Summary of Contents for CR271

Reviews:

Related manuals for CR271

Brands by name

Popular brands