background image

A2CH3 F16 – OPERATING INSTRUCTIONS 

 

 

INDEX DATE  N° 

00 06/02/09 

DC69020 

 

10/16

 

Possible cause 

How to check  

Solution 

Loose tubing, or hole in tubing 
upstream of the pump

 

Replace inlet tubing with testing 
tube running directly from inlet on 
the pump to the tank, and see if 
normal operation resumes

 

Replace defective tubing

 

Damaged bellows

 

Check to see if mist or dripping is 
coming from the muffler or from 
the PP core

 

Return the pump to SGPPL 
FRANCE, site of Charnay

 

 
 

Liquid is dripping from the pump 

 

Possible cause 

How to check  

Solution 

Manifold nut improperly/not 
enough tightened

 

Check if manifold nuts are 
properly tightened

 

Check that thread is not damaged. 
Retighten manifold nuts

 

Connection nut improperly/not 
enough tightened

 

Check if connection nuts are 
properly tightened

 

Check that thread is not damaged. 
Retighten connection nuts

 

Internal pump failure

 

Replace the pump with a new 
pump (same model) and see if 
normal operation resumes

 

Return the pump to SGPPL 
FRANCE, site of Charnay

 

Damaged bellows

 

Check to see if mist or dripping is 
coming from the muffler or PP 
core

 

Return the pump to SGPPL 
FRANCE, site of Charnay

 

 
 

VIII – Warranty 

 
Our pumps and accessories are warranted for all parts and labor against faulty workmanship (return 
to factory) for 2 years from delivery date.  
 
During the 6 following years, this warranty period of 2 years can be renewed if the maintenance of the 
pump is made using our PM kit and following the instructions included in "A2CH3 F16 – 
MAINTENANCE AND REPAIR PROCEDURES". 
 
SGPPL FRANCE is not responsible for damage to its products through improper installation, 
maintenance, use or attempts to operate them beyond their mechanical capacity, intentionally or 
otherwise, or for unauthorized repair. 
 

SGPPL FRANCE shall not be liable for any indirect, special, incidental or consequential 
damages resulting from the use, failure or malfunction of any product. 

 
 

® Teflon Du Pont's registered trademarks

 

Summary of Contents for A2CH3 F16


















Reviews: