Sagem MYC-4 Site Technical Documentation Download

Page: 15 / 109

Technical Site Documentation myC-4

Ref. SCT U38 SSC DTS 0023 – Index B - February 21, 2005

Page

2-6

2.3 DATA/AUDIO/CHARGE CONNECTOR

2.3.1 Connector description

This connector is located at the bottom of the transmission module and enable the connection to various

accessories. It comprises power supply pins and signals.

2.3.2 Signal description

SYMBOL

PIN No.

SIGNAL FUNCTION

BFTXP

Differential input from microphone

BFTXN

Differential input from microphone

BFRXP

Differential output to earphone

BFRXN

Differential output to earphone

VBAT

POWER SUPPLY IMAGE VOLTAGE, connect this signal

to «CHARGER» (pin n°1) to switch the module on.

DETECT

Accessories detection

CTS

Clear To Send

RTS

Request To Send

DSR

Data Send Ready

DTR

Data Terminal Ready

TXD1

UART transmit 1

TXD2

UART transmit 2

GND

ZERO VOLT

RXD1

UART receive 1

Ring Indicator

DCD

Data Carrier Detect

RXD2

UART receive 2

CHARGER

Phone set power ON and power supply signal.

Connector

GSM

Summary of Contents for MYC-4














































































































Search results

Summary of Contents for MYC-4

Reviews:

Related manuals for MYC-4

Brands by name

Popular brands

Sagem MYC-4, Site Technical Documentation

Search results

Summary of Contents for MYC-4

Reviews:

Related manuals for MYC-4

Brands by name

Popular brands