Sagem D20V User Manual Download Page 11

Page: 11 / 44

Handsfree

While having a conversation with your
contact, you can enable or disable the
handset loudspeaker. Press key

The icon

appears.

During communication, you can increase or
decrease the audio volume of your handset
by pressing the or key on the navigator.

Secret mode

You can switch to secret mode at any time
during your conversation. Your handset
microphone will be switched off and the other
person will not be able to hear you.

To activate secret mode:
During communication, press

key.

The

icon will appear on the screen.

To deactivate secret mode:

Press

key again. The

icon disappears.

Your caller will be able to hear you again.

Call transfer

This function is accessible if two handsets
are registered to the same base.
You can now transfer the call in progress to
another handset.

During communication, press

key.

Enter the handset number you want to call
(each handset has a different number that
appears at the left of the screen).

The handset called rings. Once someone
picks up, transfer the call by pressing the red
key .

To retake the call before it is picked up by the
handset called, press

Ending a call

At the end of the conversation, press the red
key

Intercommunication between
two handsets

You can access this function as soon as your
installation has two handsets registered on
and within the operating reach of the same
base.

ETTING

STARTED

LU 252117222C_D20V_EN.book Page 11 Mercredi, 24. août 2005 11:46 11

Summary of Contents for D20V













































Search results

Summary of Contents for D20V

Reviews:

Related manuals for D20V

Brands by name

Popular brands

Sagem D20V, User Manual

Search results

Summary of Contents for D20V

Reviews:

Related manuals for D20V

Brands by name

Popular brands