background image

WARNING

This is a design compatible component for a comprehensive 

SAFEWAZE

 Personal Fall Arrest or Fall Restraint System. Each 

component includes an instruction manual. These instructions must be 

provided to the user of this equipment prior to use. AS A USER, YOU 

MUST READ, UNDERSTAND AND FOLLOW THE MANUFACTURER’S 

INSTRUCTIONS, LABELS AND WARNINGS for each component part of 

the complete system before using it. If you do not understand the 

Instruction, Labels and Warnings for the use and maintenance of this 

component, have them explained to you. ANY MISUSE OF THIS 

COMPONENT, ANY ALTERATION OR MODIFICATION OF IT, OR 

FAILURE TO PROPERLY FOLLOW THESE USER’S INSTRUCTIONS, 

MAY RESULT IN SERIOUS INJURY OR DEATH. 

WARNING

This is an engineered system that requires trained and competent 

personnel to install.  It is understood that qualified personnel is going to 

install this system.  Because SAFEWAZE™ cannot verify that installation 

will be conducted by a “competent” person per OSHA standards, 

SAFEWAZE™

 can no longer assume the liability for the installation, or 

any liability arising due to failure to install properly.

FS-EX330-LERF

PORTABLE LEADING EDGE ROOF REACH

INSTRUCTIONS

Summary of Contents for FS-EX330-LERF




















Reviews: