SafeHome WS200X, User Manual, Page: 42 / 106

www.safehome.dk www.safehome.dk 38
39
7.3.3 Door/Window Magnetic Sensor
Power source: AAA alkaline battery 1.5 V x 2pcs (not incl.)
RF working transmission frequency: 868.35MHz +/-0.5MHz
House code: 4 Jumpers
Zone code: Pin header: 8 pin
Wireless range to Smart Panel: >100 m, open Area
7.3.4 Motion Sensor
Power source: CR123A alkaline battery x 1pc (not incl.)
RF working transmission frequency: 868.35MHz +/-0.5MHz
PIR detection angle: >110 Degree
PIR detection Range: “H”: >6 m “M”: >5 m “L”: >4 m
Wireless range to Smart Panel: >100 m, open Area
7.3.5 HD Camera
Lens 120° (Wide-Angle)
Resolution 720P / VGA / QVGA
Image enhancement Mirror / Brightness / Contrast
Camera angle Horizontal: 355° / Vertical: 90°
Triggered Alarm siren / Video record /E-mail / App notification)
RF (Radio Frequency) 868.35 MHz
Protocol TCP / IP, HTTP, etc.
Data Storage Max. 32GB MicroSD Card (not incl.)
Audio Input Built-in Mic
Working Environment Temp: 0°C ~ 40°C, Humidity:
Electricity Supply 100-240 V AC -> 5 V / 2A DC adaptor
Power 6 W
7.4 Maintenance
The product may be cleaned with a soft damp cloth and then wiped dry. Do not use abra-
sive, solvent based or aerosol cleaners as this may damage and/or discolor the product.
Do not allow water to enter or attempt to clean the inside of the unit.
Regular maintenance and inspection is recommended. In order to ensure that all com-
ponents are at optimal performance please test all components on a regular basis and
replace batteries at suitable intervals.
Tips: When you try to remove the smart panel for maintenance, it is important to disable
the tamper protection. Ensure the system is in STANDBY mode to avoid the Main Siren
sounding an alarm
7.5 Batteries
Do not allow the battery to corrode or leak as this may cause permanent damage to the
product.
Take care to insert the battery with the correct polarity as shown inside the bat-
tery compartments. Do not use rechargeable battery.
Dispose of used batteries according to local laws and regulations. DO NOT BURN.
8. Trouble Shooting and Customer Service
8.1 FAQ
Q: What is the best way to set up my system? Where should I put my Smart Panel and
the sensors?
A: We recommend that you take some time in advance to think about the placement of
the Smart Panel and Sensors. The best location for the Smart Panel is usually by the
main entry/exit point, in a hallway, or in another central location in your home. However, it
must be plugged into a power socket, which may dictate where it can be placed.
Please note that the alarm is pre-programmed with default settings, allow-
ing you a pre-determined amount of time to enter (30 seconds) and time to exit (20
seconds) before the alarm sounds. You can either change the default setting to allow
more time to enter/exit your home or, alternatively use the remote control or Camera app
to disarm the system.
Q: How many Sensors can the Smart Panel support?
A: An unlimited number of sensors can be supported by the system, added to different
zones in your house, as you see fit.
Q: What wireless range should I expect from Sensors?
A: The range will vary depending on the type of structure; however, in an open space, the
sensors should be capable of transmitting a signal up to 100 metres (300ft) from
the Smart Panel. Determine the location of the sensors first and change to a different
location for better RF performance.
Q: Do I have to programme the Smart Panel?
A: The App Controlled Camera Monitoring Home Protection System WS200X is designed
for easy installation. This means that the wireless sensors are in a default setting already
registered to the Smart Panel and will therefore function immediately after the sensors
and camera are powered up. If you choose to buy additional accessories, these will need
to be added to your system using the easy to follow instructions.
*Note: Due to the strong signal of the alarm, we advise that you change the House Code
settings following section 4.4 of this manual, if you suspect that one of your in-range
neighbors may also be using this alarm system.
Q: Can I still use the same equipment if I move and change a WiFi network?
A: The App Controlled Camera Monitoring Home Protection System WS200X is completely portable.
When you move, you can unmount your security accessories and re-install them in your new property.
If you change your WiFi network, reset the panel and all the accessories back to factory
default and then reinstall everything as per the new unit installation instructions.
Q: What if I forget my PIN?
A: If you forget your PIN, you may press the “Reset” button inside the battery compart-
ment of the Smart Panel and the PIN will be reset to the factory default PIN 1234.