background image

English  

English 

Electromagnetic Compatibility (EMC) 

01/11 

This machine has been designed in accordance with all relevant directives and standards.  However, it may still generate 
electromagnetic disturbances that can affect other systems like telecommunications (telephone, radio, and television) or 
other safety systems. These disturbances can cause safety problems in the affected systems.  Read and understand this 
section to eliminate or reduce the amount of electromagnetic disturbance generated by this machine. 
 

This machine has been designed to operate in an industrial area.  The operator must install and operate 
this equipment as described in this manual. If any electromagnetic disturbances are detected the operator 
must put in place corrective actions to eliminate these disturbances with, if necessary, assistance from 
Lincoln Electric. This equipment does not comply with IEC 61000-3-12. If it is connected to a public low-

voltage system, it is responsibility of the installer or user of the equipment to ensure, by consultation with the distribution 
network operator if necessary, that the equipment may be connected. 
 
Before installing the machine, the operator must check the work area for any devices that may malfunction because of 
electromagnetic disturbances.  Consider the following. 

  Input and output cables, control cables, and telephone cables that are in or adjacent to the work area and the 

machine. 

  Radio and/or television transmitters and receivers.  Computers or computer controlled equipment. 

  Safety and control equipment for industrial processes.  Equipment for calibration and measurement. 

  Personal medical devices like pacemakers and hearing aids. 

  Check the electromagnetic immunity for equipment operating in or near the work area.  The operator must be sure 

that all equipment in the area is compatible.  This may require additional protection measures. 

  The dimensions of the work area to consider will depend on the construction of the area and other activities that are 

taking place. 

 
Consider the following guidelines to reduce electromagnetic emissions from the machine. 

  Connect the machine to the input supply according to this manual.  If disturbances occur if may be necessary to take 

additional precautions such as filtering the input supply. 

  The output cables should be kept as short as possible and should be positioned together.  If possible connect the 

work piece to ground in order to reduce the electromagnetic emissions.  The operator must check that connecting the 
work piece to ground does not cause problems or unsafe operating conditions for personnel and equipment. 

  Shielding of cables in the work area can reduce electromagnetic emissions.  This may be necessary for special 

applications. 

 WARNING 

The Class A equipment is not intended for use in residential locations where the electrical power is provided by the public 
low-voltage supply system. There can be potential difficulties in ensuring electromagnetic compatibility in those locations, 
due to conducted as well as radio-frequency disturbances. 

 

 

Summary of Contents for PRESTOTIG 415DC

























Reviews: