• 10 •
6 TIPS FOR CHOOSING COFFEE
As a general rule any type of coffee available on the
market can be used. However, coffee is a natural product
and its
fl
avour changes according to its origin and blend;
it is therefore a good idea to try different types of coffee
in order to
fi
nd the most suited to your personal taste.
For optimal results, however, we recommend using
espresso machine blends. As a rule, Coffee should
always come out of the porta
fi
lter without any dripping.
The speed of coffee dispensing can be modi
fi
ed by
slightly changing the amount of coffee in the
fi
lter and/or
by using a different coffee grind.
Saeco recommends using single-dose coffee pods
marked ESE for a tasty coffee and easier cleaning and
preparing.
BEFORE USING THE HOT WATER/STEAM
JET, MAKE SURE THAT THE STEAM SPOUT
(PANNARELLO) IS POSITIONED OVER THE DRIP
TRAY.
7 HOT
WATER
Danger of scalding! When brewing starts, spurts
of hot water may come out. The spout can reach
high temperatures: do not touch it with bare hands.
•
(Fig.3)
- Press the ON/OFF button (2).
• Wait until the "machine ready" light (15) turns on. The
machine is now ready.
•
(Fig.18)
- Place a container or a teacup under the steam
spout (Pannarello).
•
(Fig.5)
- Open the knob (4).
•
(Fig.6)
- Switch the selection knob to the "
" position
(17).
• When the desired quantity of hot water has been
dispensed, set the selection knob (17) to the "
"
position.
•
(Fig.5)
- Close the knob (4).
• Remove the container with hot water.
8 STEAM / CAPPUCCINO
Danger of scalding! When brewing starts, spurts
of hot water may come out. The spout can reach
high temperatures: do not touch it with bare hands.
•
(Fig.3)
- Press the ON/OFF button (2).
• Wait until the "machine ready" (15) light turns on.
•
(Fig.19)
- Switch the selection knob (17) to the " "
position.
• Wait until the light (16) turns on. The machine is now ready
for steam ejection.
•
(Fig.18)
- Place a container under the steam spout.
•
(Fig.5)
- Open the knob (4) for a few seconds, so that
remaining water
fl
ows out of the steam spout (Pannarello).
In a short time only steam will come out.
• Close the knob (4) and remove the container.
• Fill 1/3 of the container you wish to use to prepare your
cappuccino with cold milk.
Use cold milk to get a better result.
•
(Fig.20)
- Immerse the steam spout in the milk and open
the knob (4) by turning it anticlockwise. Turn the milk
container with slow upward movements so that it warms
up evenly.
A maximum steam brewing of 60 seconds is
recommended.
• When brewing ends, close the knob (4) and remove the
cup with the frothed milk.
•
(Fig.19)
- Switch the selection knob (17) to the " "
position.
If both lights are on and the machine has reached a too
high temperature to brew coffee, prime the circuit as
described in section 4.5 to make the machine ready for
use.
Note: The machine is ready when the "machine
ready" light (15) is permanently on.
Note: If brewing a cappuccino as described is
not possible, prime the circuit as explained in
Section.5, then repeat the procedure.
The same procedure can be used to heat other
beverages.
• After this operation, clean the steam spout with a wet
cloth.
Summary of Contents for NINA
