background image

7 - English

FEATURES

PRODUCT SPECIFICATIONS

Size of Paper ........................................................1/4 Sheet
Motion ........................................................... Orbital Action
Orbit Diameter ......................................................... 1/16 in.

No Load Speed ................................... 14,000 r/min. (RPM)
Input ................................ 120 V, AC only, 60 Hz, 2.0 Amps

ASSEMBLY

WARNING:

Do not use this product if it is not completely assembled 
or if any parts appear to be missing or damaged. Use of 
a product that is not properly and completely assembled 
or with damaged or missing parts could result in serious 
personal injury.

WARNING:

Do not attempt to modify this product or create acces-
sories or attachments not recommended for use with this 
product. Any such alteration or modification is misuse 
and could result in a hazardous condition leading to 
possible serious personal injury.

If any parts are damaged or missing, please call 1-800-525-2579 for assistance.

OPERATION

WARNING:

Do not allow familiarity with this product to make you 
careless. Remember that a careless fraction of a second is 
sufficient to inflict serious injury.

WARNING:

Always wear eye protection with side shields marked to 
comply with ANSI Z87.1. Failure to do so could result in 
objects being thrown into your eyes resulting in possible 
serious injury.

WARNING:

Do not use any attachments or accessories not 
recommended by the manufacturer of this product. The 
use of attachments or accessories not recommended 
can result in serious personal injury.

APPLICATIONS

You may use this product for the purposes listed below:

 

Sanding on wood surfaces

 

Removing rust from and sanding steel surfaces

 

Sanding plastics

INSTALLING SANDPAPER

The cushion on the sander gives you the option of using 
either non-adhesive sandpaper that clamps to the platen or 
adhesive backed sandpaper with pressure sensitive adhesive 
backing that sticks to the cushion.

INSTALLING NON-ADHESIVE SANDPAPER

See Figure 1, page 11.

 

Unplug the sander.

 

Inspect sandpaper before installing; do not use if broken 
or defective.

 

If replacing sandpaper, remove old sandpaper. To remove 
paper, release paper clamp by lifting up on lever, and 
disengaging it from the tab on the platen.

 

Insert end of new 1/4 sheet sandpaper approximately  
1/2 in. under the paper clamp. 

 

NOTE: 1/2 in. clamping of sandpaper is necessary for 
multi-sheet stacking of paper.

 

Lift up on paper clamp lever and lock into place. Apply 
downward pressure to conform sandpaper to platen.

 

Wrap sandpaper around cushion. Lift lever on opposite 
end of sander and insert loose end of sandpaper under 
paper clamp. Fit sandpaper against cushion tightly.

 

Lift up on lever and lock into place.

Summary of Contents for S652D

































Reviews: