background image

10 - English

MAINTENANCE

Electric tools used on fiberglass material, wallboard, spack-
ling compounds, or plaster are subject to accelerated wear 
and possible premature failure because the fiberglass chips 
and grindings are highly abrasive to bearings, brushes,  
commutators, etc. Consequently, we do not recommend 
using this product for extended work on these types 
of materials. However, if you do work with any of these  
materials, it is extremely important to clean the product  
using compressed air.

LUBRICATION

All of the bearings in this product are lubricated with a  
sufficient amount of high grade lubricant for the life of the 
unit under normal operating conditions. Therefore, no further 
lubrication is required.

POWER SUPPLY CORD REPLACEMENT

If replacement of the power supply cord is necessary, this 
must be done by an authorized service center in order to 
avoid a safety hazard.

WARNING:

When servicing, use only identical replacement parts. 
Use of any other parts may create a hazard or cause 
product damage.

WARNING:

Always wear eye protection with side shields marked to 
comply with ANSI Z87.1. Failure to do so could result in 
objects being thrown into your eyes resulting in possible 
serious injury.

GENERAL MAINTENANCE

Avoid using solvents when cleaning plastic parts. Most 
plastics are susceptible to damage from various types of 
commercial solvents and may be damaged by their use. Use 
clean cloths to remove dirt, dust, oil, grease, etc.

WARNING:

Do not at any time let brake fluids, gasoline, petroleum-
based products, penetrating oils, etc., come in contact 
with plastic parts. Chemicals can damage, weaken, or 
destroy plastic which may result in serious personal 
injury.

NOTE: FIGURES (ILLUSTRATIONS) START ON PAGE 11  

AFTER FRENCH AND SPANISH LANGUAGE SECTIONS.

This product has a Three-year Limited Warranty. 

For Warranty details go to www.ryobitools.com

Summary of Contents for S652D

































Reviews: