background image

18

TROUBLESHOOTING

PROBLEM

CAUSE

REMEDY

Engine will not start.

No spark. 
 
 

No fuel.
 
 
Engine is flooded.
 
 
 
Starter  rope  pulls  harder 
now than when new.

Check spark. Remove spark plug. Reattach the spark plug cap and 
lay spark plug on metal cylinder. Pull the starter rope and watch 
for spark at spark plug tip. If there is no spark, repeat test with a 
new spark plug.
Push primer bulb until bulb is full of fuel. If bulb does not fill, primary 
fuel delivery system is blocked. Contact a servicing dealer. If primer 
bulb fills, engine may be flooded, proceed to next item.
Pull starter three times with choke lever at “RUN”. If engine does 
not start, move choke lever to “START” and repeat normal starting 
procedure. If engine still fails to start, repeat procedure with a new 
spark plug.
Contact a servicing dealer.

Engine  starts  but  will 
not accelerate.

Engine  requires  approxi-
mately  three  minutes  to 
warm up.

Allow engine to completely warm up. If engine does not accelerate 
after three minutes, contact a servicing dealer.

Engine  starts  but  will 
only run at high speed 
at half choke.

Carburetor requires 
adjustment.

Contact a servicing dealer.

Engine does not reach 
full  speed  and  emits 
excessive smoke.

Check oil fuel mixture.
Air filter is dirty. 

Spark  arrestor  screen  is 
dirty. 

Use fresh fuel and the correct 2-cycle oil mix.
Clean air filter. Refer to 

Replacing and Cleaning Air Filter earlier 

in this manual.
Contact a servicing dealer.

Engine  starts,  runs, 
and  accelerates  but 
will not idle.

Idle  speed  screw  on 
carburetor 

Turn idle speed screw clockwise to increase idle speed. 

Bar and chain running 
hot and smoking.

Check  chain  tension  for 
overtight condition
Chain oil tank empty

Tension  chain.  Refer  to 

Chain  Tension  earlier  in  this  manual. 

Check oil tank.

Motor runs, but chain 
is not rotating.

Chain tension too tight.
Check guide bar and chain 
assembly.
Check guide bar and chain 
for damage.

Retension chain. Refer to 

Chain Tension earlier in this manual.

Refer  to 

Replacing  the  Bar  and  Chain  earlier  in  this  manual. 

Inspect guide bar and chain for damage.

Summary of Contents for RY52014























Reviews: