![background image](http://html1.mh-extra.com/html/ryobi/ry4ccs/ry4ccs_operators-manual_1507299003.webp)
iii
Fig. 10
Fig. 4
Fig. 7
A - Hex screw (vis à six pans, tornillo de
hexagonal)
B - Bracket (support, soporte)
C
-
Wing nut (écrou papillon, tuerca de
mariposa)
D - Curved shaft grass deflector (déflecteur
d’herbe d’arbre courbe, deflector de pasto
del eje curvo)
A
-
Stop switch (commutateur d’arrêt,
interruptor de apagado)
B - Trigger lock out (gâchette avec verrou,
gatillo con seguro)
C - Throttle trigger (gâchette d’accélérateur,
gatillo del acelerador)
D - Starter grip and rope (poignée du lanceur et
corde, mango del arrancador y cuerda)
E - Primer bulb (poire d’amorçage, bomba
de cebado)
Fig. 5
A - Straight shaft grass deflector (déflecteur
d’herbe d’arbre droit, deflector de pasto para
eje recto)
B - Slot (fente, ranura)
C - Tab (languette, orejeta)
D - Bolt (boulon, perno)
C
B
D
A
A
B
C
D
Fig. 6
A - Oil cap/dipstick (bouchon/jauge d’huile, tapa
de relleno de aceite / varilla medidora de
aceite)
B - Hatched area (zone hachurée, área cubierta
con rayas entrecruzadas)
C - Oil fill hole (orifice de remplissage d’huile,
agujero de llenado de aceite)
D - Funnel cap (bouchon d’ entonnoir, tapa de
embudo)
A
B
C
D
B
C
E
FULL
CHOKE
RUN
HALF
CHOKE
1. PRESS PRIMER BULB 10X
2. SET TO
3. PULL UNTIL UNIT ATTEMPTS
TO START (MAX 4X)
(DO NOT PULL THROTTLE TRIGGER)
4. SET TO
5. PULL UNTIL UNIT STARTS
6. WAIT 10 SECONDS
7. SET TO
FULL CHOKE
HALF CHOKE
RUN
FULL
CHOKE
RUN
HALF
CHOKE
1. PRESS PRIMER BULB 10X
2. SET TO
3. PULL UNTIL UNIT ATTEMPTS
TO START (MAX 4X)
(DO NOT PULL THROTTLE TRIGGER)
4. SET TO
5. PULL UNTIL UNIT STARTS
6. WAIT 10 SECONDS
7. SET TO
FULL CHOKE
HALF CHOKE
RUN
1. PRESS PRIMER BULB 10X
2. SET TO
3. PULL STARTER ROPE UNTIL
THE ENGINE STARTS
(DO NOT PULL THROTTLE TRIGGER)
4. SET TO
5. WAIT 10 SECONDS
6. SET TO RUN
1. PRESS PRIMER BULB 10X
2. SET TO
3. PULL STARTER ROPE UNTIL
THE ENGINE STARTS
(DO NOT PULL THROTTLE TRIGGER)
4. SET TO
5. WAIT 10 SECONDS
6. SET TO RUN
FULL
CHOKE
RUN
HALF
CHOKE
1. PRESS PRIMER BULB 10X
2. SET TO
3. PULL UNTIL UNIT ATTEMPTS
TO START (MAX 4X)
(DO NOT PULL THROTTLE TRIGGER)
4. SET TO
5. PULL UNTIL UNIT STARTS
6. WAIT 10 SECONDS
7. SET TO
FULL CHOKE
HALF CHOKE
RUN
FULL
CHOKE
RUN
HALF
CHOKE
1. PRESS PRIMER BULB 10X
2. SET TO
3. PULL UNTIL UNIT ATTEMPTS
TO START (MAX 4X)
(DO NOT PULL THROTTLE TRIGGER)
4. SET TO
5. PULL UNTIL UNIT STARTS
6. WAIT 10 SECONDS
7. SET TO
FULL CHOKE
HALF CHOKE
RUN
1. PRESS PRIMER BULB 10X
2. SET TO
3. PULL STARTER ROPE UNTIL
THE ENGINE STARTS
(DO NOT PULL THROTTLE TRIGGER)
4. SET TO
5. WAIT 10 SECONDS
6. SET TO RUN
1. PRESS PRIMER BULB 10X
2. SET TO
3. PULL STARTER ROPE UNTIL
THE ENGINE STARTS
(DO NOT PULL THROTTLE TRIGGER)
4. SET TO
5. WAIT 10 SECONDS
6. SET TO RUN
FULL
CHOKE
RUN
HALF
CHOKE
1. PRESS PRIMER BULB 10X
2. SET TO
3. PULL UNTIL UNIT ATTEMPTS
TO START (MAX 4X)
(DO NOT PULL THROTTLE TRIGGER)
4. SET TO
5. PULL UNTIL UNIT STARTS
6. WAIT 10 SECONDS
7. SET TO
FULL CHOKE
HALF CHOKE
RUN
1. PRESS PRIMER BULB 10X
2. SET TO
3. PULL STARTER ROPE UNTIL
THE ENGINE STARTS
(DO NOT PULL THROTTLE TRIGGER)
4. SET TO
5. WAIT 10 SECONDS
6. SET TO RUN
Fig. 8
A
-
Full choke position (position de
complètement ouvert, posición de anegación
máxima)
B - Half choke position (position de demi ouvert,
posición de anegación media)
C - Run position (position de marche , posición
de marcha)
D - Choke lever (levier de volet de départ,
palanca del anegador)
A
B
C
D
D
D
A - Curved shaft trimmer (taille-bordures à
arbre courbe, recortadora de eje curvo)
B - Dangerous cutting area (zone de coupe
dangereuse, área peligrosa de corte)
C - Direction of rotation (sens de rotation,
sentido de rotación)
D
-
Best cutting area (zone d’efficacité
maximum, mejor área de corte)
B
A
C
D
Fig. 9
PROPER OPERATING POSITION
BONNE POSITION DE TRAVAIL
POSICIÓN CORRECTA PARA EL MANEJO
DE LA HERRAMIENTA
A
D