![background image](http://html1.mh-extra.com/html/ryobi/rsh2545b/rsh2545b_original-instructions-manual_1505502007.webp)
5
SHREDDING GUIDE
For best results when shredding, follow the
guidelines shown in the table below.
MATERIAL
SHREDDING METHOD
Twigs and up to
6 mm diameter.
Feed into the feeding
chute at a rate which
the product will accept
without overloading. Use
the plunger provided to
push the material into
the chute if required.
Branches and
up to 45 mm in
diameter.
Clip off all side growth
with secateurs before
feeding into the feeding
chute. Use the plunger
provided to push the
material into the chute if
required.
Bedding plants,
weeds and
shrubby growth.
Knock soil and stones
off the roots to avoid
damage to the blades.
Freshly cut
foliage, hedge,
and kitchen
waste.(I.e.
cabbage
leaves,
vegetable
peelings etc.)
With any material having
a high moisture content
it is advised to feed
in some drier sticks
at regular intervals to
help push the material
through the cutting
assembly and prevent it
from clogging.
Dry sticks and
twigs
By inserting these at the
end of your shredding
task, this will help to
clean the moisture and
plant sap from the inside
of the product and the
cutting assembly.
■
Do not allow garden waste to accumulate
before shredding as it will begin to compost,
become too damp and clog the cutting
assembly. Dry material will help most
material to clear the ejection chute. Save
some dry sticks until last to help clean the
blade area.
■
Frequently monitor the build up/collection
of shredded material.
■
The exit of the discharge chute must be
clear at all times to prevent blockages.
■
When the collection box is full, turn the
product Off before emptying.
WARNING
Do not put your hands up inside the
shredder’s discharge chute to clear away
shredded material while the product is
switched on or connected to the mains
supply. The blades are sharp. Wear heavy-
duty gloves and exercise extreme caution
when cleaning and clearing blockages.
WARNING
When feeding long woody branches/stems
into the product be careful of whip and
vibrations as the materials get caught by
the cutter. The operator must wear eye
protection whenever using the product.
WARNING
The cutting device has a tendency to pull
branches/stems into the product. Do not
try to impede entry of the material being
cut once feeding has started. Always wear
gloves to prevent skin lacerations when
feeding material into the product.
NOTE:
In normal use, do not switch off the
product until all of the shredded material has
cleared the cutter assembly. If the product is
switched off too quickly, remaining pieces of
material may clog the blade assembly and
stall the motor when the product is switched
back on.
SYMBOLS ON THE PRODUCT
Read and understand
all instructions before
operating the product, follow
all warnings and safety
instructions.
Beware of thrown or flying
objects. Keep all bystanders,
especially children and pets,
at least 15 m away from the
operating area
Danger - Rotating blades.
Keep hands and feet out of
openings while the product is
running.
Summary of Contents for RSH2545B
