![background image](http://html1.mh-extra.com/html/ryobi/p118b/p118b_operators-manual_1503772020.webp)
6 — English
P215/P215VN DRILL-DRIVER AND P235A/P235AVN IMPACT DRIVER
APPLICATIONS
You may use these producst for the purposes listed below:
P215/P215VN
Drilling and driving screws in all types of wood products
(lumber, plywood, paneling, composition board, and hard
board), ceramics, plastics, fiberglass, laminates, metals;
Driving screws into wood and drywall with screwdriver bits
P235A/P235AVN
Driving and removing screws/lag bolts; tightening screws,
nuts, and bolts
VARIABLE SPEED SWITCH TRIGGER
See Figure 1, page 10 (P215/P215VN).
See Figure 1, page 11 (P235A/P235AVN).
The variable speed switch trigger delivers higher speed with
increased trigger pressure and lower speed with decreased
trigger pressure.
To turn the drill
ON
, depress the switch trigger. To turn it
OFF
, release the switch trigger and allow the chuck to come
to a complete stop.
NOTE:
A whistling or ringing noise coming from the switch
during use is a normal part of the switch function.
NOTE:
Running at low speeds under constant usage may
cause the drill to become overheated. If this occurs, cool the
drill by running it without a load and at full speed.
DIRECTION OF ROTATION SELECTOR
(FORWARD/REVERSE/CENTER LOCK)
See Figure 1, page 10 (P215/P215VN).
See Figure 1, page 11 (P235A/P235AVN).
Set the direction of rotation selector in the
OFF
(center lock)
position to lock the switch trigger and help prevent accidental
starting when not in use.
Position the direction of rotation selector to the left of the
switch trigger for forward drilling. Position the selector to the
right of the switch trigger to reverse the direction.
NOTE:
The drill will not run unless the direction of rotation
selector is pushed fully to the left or right.
NOTICE:
To prevent gear damage, always allow the chuck to
come to a complete stop before changing the direction
of rotation.
WARNING:
Battery tools are always in operating condition. Lock
the switch when not in use or carrying at your side,
when installing or removing the battery pack, and when
installing or removing bits.
INSTALLING/REMOVING BATTERY PACK
See Figure 2, page 10 (P215/P215VN).
See Figure 2, page 11 (P235A/P235AVN).
Lock the switch trigger.
Insert the battery pack into the product as shown.
Make sure the latches on each side of the battery pack
snap into place and the battery pack is secured in the
product before beginning operation.
Depress the latches to remove the battery pack.
For complete charging instructions, see the operator’s manu-
als for your battery pack and charger.
OPERATION
INSTALLING/REMOVING BITS
See Figures 3 - 4, page 10.
The arrows on the keyless chuck indicate which direction
to rotate the chuck sleeve to tighten or release the drill bit.
Do not use a wrench to tighten or loosen the chuck jaws.
To install bits:
Lock the switch trigger and remove the
battery pack.
Open or close the chuck jaws until the opening is slightly
larger than the bit size you intend to use.
Raise the front of the drill slightly and insert the drill bit.
OPERATION
P215/P215VN DRILL-DRIVER
WARNING:
Make sure to insert the drill bit straight into the chuck
jaws. Do not insert the drill bit into the chuck jaws at
an angle, then tighten. This could cause the drill bit to
be thrown from the drill, resulting in possible serious
personal injury or damage to the chuck.
Rotate the chuck sleeve to close and tighten the chuck
jaws.
Summary of Contents for P118B
