background image

You may use the trimm

ing and routing kit

 for the

 purposes 

listed below:

    Routing all types of timber.
    Cabinet making, trimming counter tops and finishing

work.

    Trimming wood and plastics.

INSTALLING/REMOVING CUTTERS (Fig. 1)

    UNPLUG YOUR TRIMMER.

    Place your trimmer upside down on a workbench in

order to gain easy access to the spindle and collet nut.

    Place the small end of one of the wrenches provided

on the spindle flats. This will hold the spindle
stationary.

    Place the large end of the other wrench provided onto

the collet nut. Rotate wrench counterclockwise to
loosen collet nut.

APPLICATIONS

Page 4

ASSEMBLY

WARNING:

WARNING:

Failure to unplug your trimmer could result in
accidental starting causing serious injury.

WARNING:

    If installing a cutter for the first time, it can be installed

once the collet nut is loose. If changing cutters, cutter
will easily slip from collet after loosening collet nut.

    The collet is machined to precision tolerances to fit

cutters with 6.35 mm diameter shanks.

    With your trimmer still upside down on a workbench,

insert shank of cutter into collet. The shank of your
cutter should be close to but not touching the bottom of

the collet. This allows for expansion when the cutter 

gets hot.

    Tighten the collet nut securely by turning clockwise
    with the wrench provided.

TO SET 

THE 

DEPTH OF CUT (Fig. 2)

   

 UNPLUG YOUR TRIMMER

    Loosen the wing bolt and move the base until the tip of
    cutter touches the work surface. The depth of cut is

zero at this point.

    Position your trimmer so that the cutter can extend

below the sub base for desired depth of cut setting.
Move the base to obtain the desired depth of cut. The
distance the cutter moves will be indicated on the
depth of cut scale. Each mark on the scale indicates a
1.6 mm change in depth setting. Indicator points are
located on the base.

    Securely tighten the wing bolt.

ASSEMBLY

Wrench On
Collet Nut

Cutter

Wrench On
Spindle Flats

Fig. 1

If you are changing a cutter immediately after
use, be careful not to touch the cutter or collet
with your hands or fingers. They may get burnt
due to the heat buildup from cutting.
Always use the wrench provide.

Your trimming and routing kit should never be
connected to a power supply when you are
assembling parts, making adjustments,
installing or removing cutters, or when not in
use. Disconnecting your trimmer will prevent
accidental starting that could cause serious
injury.

WARNING:

If collet nut is not tightened securely, cutter
may come out during use, causing serious
personal injury.

WARNING:

Avoid open area of trimmer base. Serious
personal injury will result from contact with a
rotating cutter.

WARNING:

Failure to unplug your trimmer could result in
accidental starting causing serious injury.

WARNING:

Do not use cutters that are larger in diameter
than the opening in trimmer base. Use of
such cutters will come in contact with the
trimmer base and damage both the cutter
and trimmer base. Possible loss of control or
create other hazardous conditions that could
cause possible serious personal injury.

WARNING:

Do not use cutters with undersized shanks.
Undersized shanks will not tighten properly
and could be thrown from tool causing injury.

Summary of Contents for EVT400K









Reviews: