background image

Using the sanding belt

1. Turn on the belt & disc sander.
2. Position the workpiece on the 

table and hold it firmly with 
both hands ensuring that you 
keep your fingers away from 
the sanding belt.

3. Keep the end butted against 

the backstop and move the 
workpiece evenly across the 
sanding belt. 

4. Use extra caution when sanding 

very thin pieces.

Maintenance

All the bearings are sealed ball bearings, 
lubricated for life, and require no
require no maintenance.
 

Cleaning

1. Keep the tool’s air vents unclogged 
and clean at all times.

2. Remove dust and dirt regularly. 
Cleaning is best done with a soft
brush or a rag. 
3. Re-lubricate all moving parts at 
regular intervals.
4. Never use caustic agents to clean 
plastic parts.

CAUTION.

 

Do not use cleaning agents 

 A mild detergent on a damp cloth is 
recommended.

General inspection

Regularly check that all the fixing screws
are tight. They may vibrate loose over time. 

Repairs

Only an authorised Ryobi service centre 
should replace the cordset or carry out 
other repairs. If the cordset is damaged 
or worn, have it repaired or replaced by 
it repaired or replaced by an authorised 
Ryobi service agent.

to clean the plastic parts of the tool.

EMBS200 MANUAL 2  5/5/05  2:57 PM  Page 13

Summary of Contents for EMBS200

















Reviews: