5
ENGLISH
ADJUSTMENTS
■
Inspect the replacement wheel for defects such as cracks,
chipping, and correct speed rating. If defects are found or
the speed rating is not greater than 4800min
1
,stop using
the wheel. Select another wheel.
■
Clean debris from the inner washer and inner flange.
■
Place new wheel over spacer, then place both on wheel
arbor against inner flange.
■
Clean outer flange, then align flats with flats on wheel arbor
and slide it onto arbor until it is flushed against wheel.
■
Place recessed side of outer washer against arbor, then
insert wheel bolt into threaded end of wheel arbor.
■
Start threads and turn bolt clockwise to snugly tighten.
■
Pull the spindle lock button and rotate bolt until spindle
being locked. This will prevent shaft from rotating.
■
Using the wrench provided, securely tighten wheel bolt.
Note:
Bolt has right hand threads. Turn bolt clockwise to
tighten.
WARNING:
Do not overtighten wheel bolt. Overtightening can cause
the new wheel to crack, resulting in premature failure and
possible serious personal injury.
PROTECTION GUARD
■
In order to avoid spark splashing, under the operational
condition, loose the screw and adjust angle of the protection
guard.
ADJUSTABLE FENCE (Fig. 4)
The adjustable fence is located at the rear of your cut-off
machine. It is used along with the vice clamp to provide a
clamp for holding your workpiece securely when making cuts.
It also makes your cut-off machine more versatile.
The fence can be rotated to obtain cutting angles from 0° to
45° (L&R). It can also be moved back to allow greater cutting
widths in thin stock, or moved forward to allow greater cutting
depths in tall or thick stock.
CUTTING ANGLE ADJUSTMENT (Fig. 4)
■
Unplug your cut-off machine.
WARNING:
Failure to unplug cut-off machine could result in accidental
starting causing possible serious personal injury.
■
Loosen the fence quick lock, by using the wrench supplied.
Then loosen the fence bolt to secure the adjustable fence.
■
Rotate fence until the desired angle of cut on the scale is
aligned with the indicator in machine base.
■
For precise cuts, check the angle of cut for the fence
against the abrasive wheel with a protractor, bevel square,
or other similar device.
■
Tighten the fence quick lock, by using the wrench supplied,
then securely tighten fence bolt. Return wrench to its
storage area in the base.
■
This will secure the fence in place at desired angle.
ADJUSTING WIDTH OF CUT (Fig. 5-6)
■
Unplug your cut-off machine.
WARNING:
Failure to unplug cut-off machine could result in accidental
starting causing possible serious personal injury.
■
The default space between the vice and the fence is 0 mm
min. to 170 mm max. By following the below adjustment
procedures, it is possible to increase that distance so that
the vice is between 35 mm and 205 mm or 70 mm and 240
mm from the fence.
WARNING:
Bevel cutting angle is not suitable for the above 2 suggested
width of cuts.
■
To increase the width of cut of your cut-off machine, loosen
and remove the fence quick lock and washer. The use the
wrench supplied to loosen and remove the fence bolt and
washers to secure fence to machine base.
■
Reposition the curved slot of the fence with the threaded
hole (b) at the back of the machine base.
■
Install a fence quick lock through a flat washer into machine
base. Do not tighten fence quick lock bolt securely.
■
Align remaining fence bolt hole with the middle threaded
hole (a) of the machine base.
■
Install fence bolt through lock washer and flat washer into
machine base.
■
Check and adjust fence to 0
o
cutting angle.
■
Securely tighten fence quick lock and fence bolts.
■
This position is good for cutting thin and wide pieces of
stock, such as flat or angled stock.
■
To increase the height of cut of your cut-off machine, follow
the above procedure except place the rear fence bolt in the
middle threaded hole (a) and the front fence bolt in the front
threaded hole.
■
Check and adjust fence to desired cutting angle.
■
Using the wrench provided, securely tighten fence quick
lock en fence bolts. Return hex key to its storage area in
base.
■
This position is good for cutting tall and thick pieces of
stock, such as square or tube stock.
LOCK LEVER (Fig. 7-8)
The lock lever engages the vice clamp. It can be used along
with the fence to provide a vice for securing the workpiece to
be cut.
■
It also allows you to open and close the vice quickly without
repetitive turning the vice crank handle.
USING THE QUICK LOCK-RELEASE LEVER
AND VICE CLAMP (Fig. 7-8)
To loosen:
■
Unplug your cut-off machine.
Summary of Contents for ECO2437
