4
ENGLISH
FEATURES
ADJUSTABLE FENCE
The fence on your cut-off machine has been provided to
support the workpiece and provide clamping support to
the vice for holding your workpiece securely when making
all cuts. It is an adjustable fence that has been provided to
make your cut-off machine more versatile. It adjusts from
0
o
to 45
o
(L&R) for making angled cuts. The hole pattern
allows it to be moved forward when making cuts in tall or
thick stock, such as square stock or tube stock. The hole
pattern allows it to be moved back when making cuts in
stock that is thin or wide, such as angle stock.
QUICK LOCK-RELEASE LEVER
A lock lever has been provided on your cut-off machine This
feature allows you to open and close the vice clamp quickly
without repetitive turning of the vice crank handle.
CARRYING HANDLE
For convenience when carrying or transporting your cut-off
machine from one place to another, a carrying handle has
been provided on top of the machine arm .
To transport, turn off and unplug your machine, then lower
machine arm and lock it in the down position. Use the
transport chain to lock machine arm in the down position.
SPINDLE LOCK BUTTON
A spindle lock button has been provided for locking the
spindle whilst changing the abrasive wheel.
Pull the spindle lock button while installing, changing, or
removing wheel only.
ADJUSTMENTS
WARNING:
To prevent accidental starting that could cause possible
serious personal injury, assemble all parts to your cut-off
machine before connecting it to power supply. Machine
should never be connected to power supply when you are
assembling parts, making adjustments, installing or removing
wheels, or when not in use.
As mentioned previously your cut-off machine has been
factory assembled and adjusted. After extended use and
wear, the wheel will need to be replaced with a new one.
WARNING:
A 355 mm wheel is the maximum wheel capacity of your
cut-off machine. Never use a wheel that is too thick to allow
outer flange to engage with the flats on the spindle. Larger
wheels will come in contact with the wheel guards, while
thicker wheels will prevent the bolt from securing the wheel on
the spindle. Either of these situations could result in a serious
accident and can cause serious personal injury.
REMOVAL AND INSTALLATION OF THE
WHEEL (Fig. 3)
■
Unplug your cut-off machine.
WARNING:
Before performing any adjustment, make sure the tool
is unplugged from the power supply. Failure to heed this
warning could result in serious personal injury.
■
Push down on machine arm and remove chain from hook
on motor housing to release machine arm.
■
Raise machine arm to its full lifted position. Be cautious
when raising, machine arm is spring loaded.
■
Pull lower wheel guard upward, exposing wheel bolt that
secures abrasive wheel to wheel arbor.
■
Pull the spindle lock button and rotate bolt until spindle
locks, preventing shaft from rotating.
■
Using the Wrench provided, to loosen and remove
bolt. Note: Bolt has right hand threads. Turn bolt
counterclockwise to loosen.
■
Remove outer washer, outer flange , and wheel. Do not
remove spacer, inner flange and inner washer. Removal of
these three parts are not required for wheel changes.
WARNING:
If spacer, inner flange or inner washer has been removed,
replace those parts before placing on wheel arbor. Failure
to do so could cause an accident since wheel will not tighten
properly.
TO INSTALL (Fig. 3)
■
Unplug your cut-off machine.
WARNING:
Failure to unplug cut-off machine could result in accidental
starting causing possible serious personal injury.
Summary of Contents for ECO2437
