![background image](http://html1.mh-extra.com/html/ryobi/chi1442p/chi1442p_user-manual_1504369014.webp)
10
English
GB
D
E
I
P
NL
S
DK
N
GR
H
CZ
RUS
RO
FIN
FR
SLO
HR
TR
PL
OPERATION
Charger: BC-1440/BC-1415-S/BC-1800/BC-1815-S
See Figure 8.
LED WILL BE ON TO INDICATE STATUS OF
CHARGER AND BATTERY PACK
■
Red LED on = Fast charging mode.
■
Green LED on = Fully charged battery pack.
■
No LED on = Defective charge or battery pack
.
■
When your battery pack becomes fully charged, the
red light will turn off and the green light will turn on.
■
After normal usage, 1 hour of charge time is required
to be fully charged. A minimum charge time of 1 to
1-1/2 hours is required to recharge a completely
discharged tool.
■
DO NOT place charger in an area of extreme heat
or cold. It will work best at temperatures above 10°C
and below 38°C
IMPORTANT INFORMATION FOR RECHARGING HOT
BATTERIES
When using your tool continuously, the batteries in your
battery pack will become hot. You should let a hot battery
pack cool down for approximately 30 minutes before
attempting to recharge.
TO INSTALL BATTERY PACK
■
Lock switch trigger on your drill by placing the
direction of rotation selector in center position.
See Figure 4.
■
Place battery pack in your drill. Align raised rib on
battery pack with groove inside drill.
See Figure 2.
■
Make sure the latches on battery pack snap in place
and battery pack is secured in drill before beginning
operation.
TO REMOVE BATTERY PACK
■
Lock switch trigger on your drill by placing the
direction of rotation selector in center position.
See Figure 4.
■
Locate latches of battery pack and depress to release
battery pack from your drill.
See Figure 2.
■
Remove battery pack from your drill.
ADJUSTING THE TORQUE
See Figure 3.
The tool is equipped with an adjustable torque clutch for
driving different types of screws into different materials.
Adjust the torque as necessary.
We recommend that you use carbide-tipped bits and
select impact mode when drilling in hard material such as
brick, tile, concrete, etc.
CAUTION
The impact drill is not designed for reverse
hammering. Failure to obey this caution may
result in property damage.
SWITCH
See Figure 4.
■
To turn your drill ON, depress the switch trigger.
■
To turn it OFF, release the switch trigger.
VARIABLE SPEED
This tool has a variable speed switch that delivers higher
speed and torque with increased trigger pressure. Speed
is controlled by the amount of switch trigger depression.
SWITCH LOCK
See Figure 4.
The switch trigger can be locked in the OFF position.
This feature can be used to prevent the possibility of
accidental starting when not in use. To lock switch trigger,
place the direction of rotation selector (Forward/Reverse
Selector) in center position.
Note:
When selector is in center position, switch trigger
is locked.
REVERSIBLE
See Figure 4.
This tool has the feature of being reversible. The direction
of rotation is controlled by a selector located above the
switch trigger. With the drill held in normal operating
position, the direction of rotation selector should be
positioned to the left of the switch for drilling. The drilling
direction is reversed when the selector is to the right
of the switch. When the selector is in center position,
the switch trigger is locked. To stop, release switch trigger
and allow the chuck to come to a complete stop.
ELECTRIC BRAKE
This drill has an electric brake. When the trigger switch
is released, the chuck stops turning. When the brake is
functioning properly, sparks will be visible through the
vent slots on the housing. This is normal and is the action
of the brake.
10
960931157-01.indd 10
960931157-01.indd 10
7/10/07 10:45:09 AM
7/10/07 10:45:09 AM