![background image](http://html1.mh-extra.com/html/ryobi/ccc-1801m/ccc-1801m_user-manual_1506163005.webp)
1
English
EN
FR
DE
ES
IT
NL
PT
DA
SV
FI
NO
RU
PL
CS
HU
RO
LV
LT
ET
HR
SL
SK
EL
TR
DESCRIPTION
1. Heavy-duty scrubbing pad (red)
2. Light scrubbing pad (white)
3. Polishing pad (gray)
4. Sanding sheet
5. Hook-and-loop pad
6. On/Off switch
7. Latch
8. Battery Pack (Not Included)
9. Fuzzy side
OPERATION
WARNING
Do not allow familiarity with tools to make you
careless. Remember that a careless fraction of a
second issufficient to inflict serious injury.
WARNING
Always wear safety goggles or safety glasses
with side shields when operating tools. Failure
to do so could result in objects being thrown into
your eyes, resulting inpossible serious injury.
WARNING
Do not use any attachments or accessories
not recommended by the manufacturer of this
tool. The use of attachments or accessories not
recommended can result in serious personal injury.
APPLICATIONS
You may use this tool for the following purposes:
■
Sanding on wood surfaces
■
Removing rust from and sanding steel surfaces
■
Polishing and scrubbing porcelain and metal
TO INSTALL BATTERY PACK (NOT INCLUDED)
(Fig. 2)
WARNING
Always be sure the switch is in the OFF (O)
position before installing the battery pack. Failure
to do so could cause accidental starting, leading
to serious personal injury.
■
Place the battery pack in the sander. Align the raised
rib on the battery pack with the groove inside the
sander, then slide the battery pack into the sander.
■
Make sure the latches on each side of your battery
pack snap into place and the battery pack is secured
in the sander before beginning operation.
CAUTION
When placing battery pack in the tool, be sure
raised rib on battery pack aligns with the bottom
of the drill and latches into place properly.
Improper installation of the battery pack can
cause damage to internal components.
■
Make sure the latches on each side of the battery
pack snap into place and the battery pack is secured
in the drill before beginning operation.
TO REMOVE BATTERY PACK (NOT INCLUDED)
■
Locate the latches on the side of the battery pack
and depress them to release the battery pack from
the sander.
■
Remove battery pack from the sander.
BATTERY PROTECTION FEATURES
Ryobi 18 V lithium-ion batteries are designed with
features that protect the lithium-ion cells and maximize
battery life. Under some operating conditions, these
built-in features may cause the battery and the tool it is
powering to act differently from nickel-cadmium batteries.
During some applications, the battery electronics may
signal the battery to shut down, and cause the tool to
stop running. To reset the battery and tool, release the
trigger and resume normal operation.
NOTE:
To prevent further shut down of the battery, avoid
forcing the tool.
If releasing the trigger does not reset the battery and
tool, the battery pack is depleted. If depleted, the battery
pack will begin charging when placed on the lithium-ion
charger.
OPERATION
WARNING
Battery tools are always in operating condition.
Therefore, switch should always be locked when
not in use orcarrying at your side.
SANDING SHEET AND PAD SELECTION
Selecting the correct size grit and type sandpaper is
an extremely important step in achieving a high quality
sanded finish. Aluminum oxide, silicon carbide, and
other synthetic abrasives are best for power sanding.
Natural abrasives, such as flint and garnet, are too soft
for economical use in power sanding.
In general, coarse grit will remove the most material
and finer grit will produce the best finish in all sanding
operations. The condition of the surface to be sanded
will determine which grit will do the job. If the surface is
rough, start with a coarse grit and sand until the surface
is uniform. Medium grit may then be used to remove
scratches left by the coarser grit and finer grit used for
finishing of the surface. Always continue sanding with