manualshive.com logo in svg

Rycom 8879, User Manual, Page: 21 / 24

Share
Download
Rycom 8879 User Manual Download Page 21

Depth Measurement When Using the Sonde

Once the S

ONDE

has been located, the depth can then be found. Refer to the figure below for a reference.

Start by moving the R

ECEIVER

along the path behind the S

ONDE

with the antenna in line with the S

ONDE

and

find a NULL between the PEAK ghost signals. Mark this point (A). Then move the R

ECEIVER

along the path

in front of the S

ONDE

and find another NULL. Mark this point (B). Next, measure the distance between these

two points. The depth of the pipe is 0.7 times the distance between the two points. 

The 8879 is specially designed to measure the S

ONDE

depth digitally. To use this feature, the R

ECEIVER

must

be placed in the position shown in the diagram above. The R

ECEIVER

antenna must be in line with the

S

ONDE

. The R

ECEIVER

must also be in the S

ONDE

mode. Locate the S

ONDE

as described previously. When

the S

ONDE

has been located, press the DEPTH button. The LCD display will indicate dEP, SON and display

the depth of the S

ONDE

in feet or meters. 

20

Summary of Contents for 8879

























Reviews:

No comments