manualshive.com logo in svg

Rycom 8879, User Manual, Page: 11 / 24

Share
Download
Rycom 8879 User Manual Download Page 11

Locating the Cable or Pipe

Make sure the T

RANSMITTER

is connected and in the ON position. Then move approximately 15 feet (4.5 meters) away

from the T

RANSMITTER

along the path. (Move about 25 feet (7.5 meters) for the Inductive search mode.)

Hold the R

ECEIVER

so that you can see the LCD bargraph and controls easily. Make sure the R

ECEIVER

and the

T

RANSMITTER

FREQUENCY are both set for the same FREQUENCY, either 815 Hz (lower), 8 kHz or 82 kHz (higher).

Or select the passive locating mode which do not require the transmitter

Selecting the Locating Mode (Peak or Null)

Press the MODE button to select the desired Peak or Null locating method. 

Peak Mode Locating

Keep the R

ECEIVER

in a vertical position. Move the R

ECEIVER

left to right across the path. When the R

ECEIVER

is directly above the cable or pipe, rotate the R

ECEIVER

for a maximum signal. As you move the R

ECEIVER

away from the cable path, the meter reading (and audio frequency response) will drop off. 

If you rotate the R

ECEIVER

while over the cable, a sharp NULL will identify the cable’s direction. It is aligned

with the flat side of the R

ECEIVER

.

10

Peak Mode

Receiver Max

Signal over cable

Buried cable

(End view)

(End view)

Receiver Min

Signal over cable

Null Mode

Buried cable

Summary of Contents for 8879

























Reviews:

No comments