background image

ROYAL ENFIELD WORKSHOP MANUAL 

 

 

After  removal  of  the  fork  head  the  lamp 

bracket  tubes  can  be  lifted  straight  off  and  the 
springs can be withdrawn from the upper end of 
the main tubes. 

7. Removal of Main Tubes 

To remove the main tubes first dismantle the 

fork as described in paragraph 3 then remove the 
facia panel fork head and lamp bracket tubes as 
described  in  paragraph  6.  Now  remove  one  nut 
from  each  of  the  fork  crown  clamp  studs, 
remove the studs and separate the clamp sleeves 
with  a  drift  of  the  form  shown  in  Fig.  4.  Now 
knock  the  main  tubes  out  of  the  fork  crown 
either  upwards  or  downwards  as  may  be  most 
convenient.  If  the  machine  has  been  in  an 
accident  and  the  tube  is  badly  bent  both  above 
and  below  the  fork  crown,  it  may  be  necessary 
to cut through the tube with a hacksaw before  it 
can be withdrawn. 
 

8. Reassembly of Parts 

No  difficulty  should  be  experienced  with 

this.  When  refitting  the  main  tube  use  the  lamp 
bracket tube as a guide to its correct position in 
the  fork  crown.  The  small  shoulder  some  1.1/2 
in. from the upper end of the tube should be 1/8 
in. above the top of the lamp bracket tube when 
the latter is in position on the fork crown. With 
the  main  tube  in  this  position  tighten  the  fork 
crown  clamp  screws  before  fitting  the  facia 
panel fork head. 

The  cover  tube  must  be  fitted  in  position  on 

the  fork  crown  and  the  clamp  sleeves  placed  in 
position  before  the  main  tube  is  fitted.  To  keep 
the clamp sleeves in position  it is convenient to 
insert  a  short  piece  of  tube  or  bar  in  the  eye  of 
the  fork  crown  before  putting  the  cover  tube  in 
position. The short piece of tube will be pushed 
out  when  inserting  the  main  tube.  Before 
tightening  the  nuts  on  the  three  fork  head  clip 
bolts  make  sure  that  the  bolt  heads  and  the 
sleeves  are  correctly  positioned  with  the 
cut-away  portion  engaging  the  main  tube  or 
steering  stem.  Failure  to  do  this  may  result  in  a 
cracked fork head. 

When  refitting  the  oil  seal  or  fitting  a  new 

one great care must be exercised not to damage 
the  synthetic  rubber  lip  which  forms  the  actual 
seal.  If  the  seal  has  been  removed  from  the 
upper end of the main tube and is refitted from 
this  end  a  special  nose  piece  (Fig.  5)  must  be 
fitted  over  the  end  of  the  tube  to  prevent  the 
thread from damaging the oil seal. 

The spring stud is a tight fit in the hole at the 

lower end of the bottom tube. Once the stud has 
been entered in the hole push the bottom tube up 
sharply  against  the  spring  until  two  or  three 
threads  on  the  stud  project  beneath  the  end  of 
the bottom tube. Now fit the nut and washer and 
pull the stud into position by tightening the nut. 
If  necessary  fit  the  nut  first  without  the  washer 
until sufficient thread is projecting to enable the 
washer to be fitted. 
 

9. Lubrication 

The lubrication of the fork bearings is elected 

by  the  oil  which  forms  the  hydraulic  damping 
medium.  All  that  is  necessary  is  to  keep 
sufficient  oil  in  the  fork  to  ensure  that  the  top 
end of the bottom spring stud is never uncovered 
even  in  the  full  rebound  position.  The  level  of 
oil  in  the  fork  can  be  gauged  by  removing  the 
top  plug  screw  and  inserting  a  long  rod  about 
3/8 in. diameter. If slightly tilted this  will ledge 
against  the  nut  at  the  upper  end  of  the  bottom 
spring  stud  and  indicate  the  level  of  oil  above 
the  stud.  If  the  fork  is  empty  to  start  with  the 
quantity  required  is  approximately  7.1/2  fluid 
ounces in each leg. Recommended grades of oil 
are Castolite, Mobiloil Arctic, Essolube 20, B.P. 
Energol S.A.E. 20 and Shell X-100 20/20 w. 

Section J3   Page 4 

www.hitchcocksmotorcycles.com

Summary of Contents for 350 BULLET 1949







































































































Reviews: