Royal Enfield 350 BULLET 1949 Page 26 Workshop Maintenance Manual Download

Page: 26 / 102

ROYAL ENFIELD WORKSHOP MANUAL

SECTION E1

Gearbox and Clutch

" Meteor 700" " 500 Twin " " 500 Bullet" " 350 Bullet

1. Removal of Gearbox

This is described in section Dl or D2. The gearbox

can, however, be completly dismantled with the
engine in the frame except for removal of the inside
operator and the bearings in the gearbox shell.

2. To Dismantle the Gearbox

First remove the kickstart crank, the gear

changelever and the neutral finder and pointer.

Remove the top small inspection cover and

disconnect the clutch cable.

Remove four screws and the gearbox outer

cover can then be detached.

Remove the gear change mechanism by taking

off the two nuts securing it.

Remove the main shaft bearing cover which

is attached by two screws.

Remove four cheese-headed screws and

hexagon bolt.

Remove the spring box locating plunger nut

and washer.

Remove the main shaft nut

(Left Hand Thread).

The gearbox inner cover can then be removed

The mainshaft can be drawn straight out if the

clutch has been removed, which, however, should
be done before taking off the gearbox cover.

Section E1 Page 1

www.hitchcocksmotorcycles.com

Summary of Contents for 350 BULLET 1949







































































































Search results

Summary of Contents for 350 BULLET 1949

Reviews:

Related manuals for 350 BULLET 1949

Brands by name

Popular brands

Royal Enfield 350 BULLET 1949, Workshop Maintenance Manual

Search results

Summary of Contents for 350 BULLET 1949

Reviews:

Related manuals for 350 BULLET 1949

Brands by name

Popular brands