Royal Enfield 350 BULLET 1949 Page 9 Workshop Maintenance Manual Download

Page: 9 / 102

ROYAL ENFIELD WORKSHOP MANUAL

12. Timing Drive

The cams are located in the timing chest and

are driven at half engine speed from the
crankshaft by a positive geared drive.

The magdyno is driven from the inlet cam

pinion through two idler pinions which also act as
a gear pump to return the oil from the timing
chest to the oil tank.

13. Ignition and Lighting System

The lighting and ignition are supplied from a

Lucas Magdyno, which consists of a magneto

running at 1/2 engine speed and a dynamo
running at 1.1/2 engine speed.

14. Carburetter (See Sections F1 and
F2).

350 c.c. Engine Amal Type 276CX/lA.
Amal Type 376/29 Monobloc.
500 c.c. Engine Amal Type 289T/lA.

15. Air Filter

The air supply to the carburettor is cleaned by

a Vokes Micro-Vee felt and gauze dry filter,

Section B2 Page 2

www.hitchcocksmotorcycles.com

Summary of Contents for 350 BULLET 1949







































































































Search results

Summary of Contents for 350 BULLET 1949

Reviews:

Related manuals for 350 BULLET 1949

Brands by name

Popular brands

Royal Enfield 350 BULLET 1949, Workshop Maintenance Manual

Search results

Summary of Contents for 350 BULLET 1949

Reviews:

Related manuals for 350 BULLET 1949

Brands by name

Popular brands