manualshive.com logo in svg

Roving Networks RN-171, User Manual And Command Reference

Share
Download
Roving Networks RN-171 User Manual And Command Reference Download Page 3

WiFly GSX

 

www.rovingnetworks.com

 

 

 

 

 

WiFlyRN171-um      2/23/2011

 

809 University Avenue 

•

 Los Gatos, CA 95032  

•

Tel (408) 395-6539 

•[email protected]

 

~

 

3

 

~

 

12.1.  Associate with a network access point............................................................................................41 
12.2. Making 

Connections .......................................................................................................................42 

12.3.  Setting up Automatic Connections .................................................................................................42 
12.4.  Controlling Connections using PIO5 and PIO6..............................................................................43 
12.5. Using 

DNS 

settings.........................................................................................................................43 

12.6.  Utilizing the Backup IP address/connect function..........................................................................44 

13. 

Using HTML client feature

........................................................................................................................ 45

 

13.1.  Built-in HTML Client Modes .........................................................................................................45 
13.2.  Automatically periodicallyconnect to web server...........................................................................46 
13.3.  Automatically connect to web server on uart data..........................................................................46 
13.4. Posting 

binary 

data:.........................................................................................................................47 

13.5.  Auto posting sensor data:................................................................................................................48 
13.6.  Examples using the HTML client ...................................................................................................48 

14. 

Firmware Upgrade over FTP

..................................................................................................................... 51

 

14.1.  FTP Upload and Upgrade ...............................................................................................................51 

15. Adhoc 

Networking 

Mode

........................................................................................................................... 53

 

15.1.  Infrastructure and adhoc comparison..............................................................................................53 
15.2.  Configuring adhoc mode.................................................................................................................53 

16. 

Analog Sensor Capability

.......................................................................................................................... 56

 

16.1.  Automatic sampling of sensor pins:................................................................................................57 
16.2.  Using the Built In Sensor Power.....................................................................................................57 

17. Default 

Configuration 

Settings

.................................................................................................................. 59

 

17.1.  Restoring Default configuration settings: .......................................................................................60 

18. Boot-up 

Timing 

Values

............................................................................................................................... 61

 

19. Supported 

Access 

Points

............................................................................................................................ 62

 

20. Release 

Notes

.............................................................................................................................................. 63

 

20.1. Known 

problems.............................................................................................................................63 

20.2.  Current Firmware features and fixes...............................................................................................63 

 

 
 

 
 
 
 
 
 
 
 
 
 
 
 

Summary of Contents for RN-171








































































Reviews:

No comments

Brands by name

Popular brands

Load more brands