Roving Networks RN-171 User Manual And Command Reference Download Page 23

Page: 23 / 71

WiFly GSX

www.rovingnetworks.com

WiFlyRN171-um 2/23/2011

809 University Avenue

•

Los Gatos, CA 95032

•

Tel (408) 395-6539

•[email protected]

Turn off the sensor power

GROUND the sensor pin

1.2V internal regulated reference

VBATT input pin

3.3V output of on board regulator

Example:

To set the power to 1.2V automatically upon power up, the

command would be

set q power 0x20

. To set sensor power to 1.2V when

sampling event occurs, the command is

set q power 0x02

Example:

To set the power to 3.3V automatically upon power up, the

command would be

set q power 0x40

. To set sensor power to 3.3V when

sampling event occurs, the command is

set q power 0x04

Get Commands

These commands begin with “get”. They display the current values.

get adhoc

display all adhoc settings.

get broadcast

will display the broadcast UPD address, port and interval

get everything

displays all configuration settings, useful for debug.

get com

display comm. settings.

getdns

display DNS settings.

get ftp

display FTP settings.

getip<a>

display IP address and port number settings

Optional parameter just returns the

current IP address value.

get mac

display the device MAC address

get option

display the option settings like device ID

get q

display the sensor settings (sensor mask and sensor power settings)

get sys

display system settings, sleep, wake timers, etc.

get time

display the time server UDP address and port number

getwlan

display the ssid, chan, and other wlan settings

Summary of Contents for RN-171








































































Search results

Summary of Contents for RN-171

Reviews:

Brands by name

Popular brands

Roving Networks RN-171, User Manual And Command Reference

Search results

Summary of Contents for RN-171

Reviews:

Brands by name

Popular brands