manualshive.com logo in svg

Roving Networks RN-171, User Manual And Command Reference

Share
Download
Roving Networks RN-171 User Manual And Command Reference Download Page 22

WiFly GSX

 

www.rovingnetworks.com

 

 

 

 

 

WiFlyRN171-um      2/23/2011

 

809 University Avenue 

•

 Los Gatos, CA 95032  

•

Tel (408) 395-6539 

•[email protected]

 

~

 

22

 

~

 

9 9 

Mbit/sec 

10 12 

Mbit/sec 

11 18 

Mbit/sec 

12 

24 Mbit/sec  (default) 

13 36 

Mbit/sec 

14 48 

Mbit/sec 

15 54 

Mbit/sec 

 
 

 
setwlanssid<string>

 

sets the wlanssid to associate with.  1-32 chars. 

 
 

NOTE:

  If the passphrase or ssid contain the SPACE ( ‘ ‘) 

 

characterS, these can be entered using substitution via the “$”  character.  

 

 

For example, if the ssid of the AP is “yellow brick road”  

 You 

would 

enter 

“yellow$brick$road” 

 

 

 

Using the ‘get w” command will properly display the value: 

 

SSID=yellow brick road. 

 

setwlan window <value>

 

sets the IP maximum buffer window size.  Default is 1460 bytes. 

 

5.12.

 

Sensor Parameters 

 
set q sensor  <mask>

 

Bitmask value that determines which sensor pins to sample when sending 
data using the UDP broadcast packet,  or the HTTP auto sample function. 

NOTE

: The sensor pins variable has been changed from

 

 

   

“set option sensor <mask>” to set q sensor <mask> in ver 2.21.1 

 

 
set q power <value>   

This is a new register added in ver 2.21.1 to automatically turn on the       
sensor power. This is a 8 bit register with two 4 bit nibbles. If the top nibble is 
set, then power is applied upon power up and removed upon power down or 
sleep.  
 
If the bottom  nibble is set, then power is applied when a sampling event 
occurs, for example: 

•

 

The UDP Broadcast 

•

 

The auto web posting of sensor data 

The power is removed immediately after the sampling is complete. 
The values used for setting the power are described in the table below: 
 

Value 

Sensor pin voltage 

Summary of Contents for RN-171








































































Reviews:

No comments

Brands by name

Popular brands

Load more brands