manualshive.com logo in svg

Roving Networks RN-171, User Manual And Command Reference

Share
Download
Roving Networks RN-171 User Manual And Command Reference Download Page 26

WiFly GSX

 

www.rovingnetworks.com

 

 

 

 

 

WiFlyRN171-um      2/23/2011

 

809 University Avenue 

•

 Los Gatos, CA 95032  

•

Tel (408) 395-6539 

•[email protected]

 

~

 

26

 

~

 

ping g

 

pings the gateway, the gateway IP address is loaded if DHCP 

is turned on, otherwise it should be set with the 

set ip gateway <addr>

 

command 
 

ping h

 

pings the stored host IP address, the host IP address can be set 

with the 

set ip host <addr>

command 

ping i

 

pings a known Internet server at www.neelum.com by first 

resolving the URL (proves that DNS is working and proves the device has 
internet connectivity). 

ping 0

 

terminates a ping command 

 

reboot  

 

forces a reboot of the device (similar to power cycle) 

 

scan<time><P> 

Performs an active probe scan of access points on all 13 channels. Returns 
MAC address, signal strength, SSID name, security mode. 

 

Default scan time is 200ms / channel = about 3 seconds. 

time is

 an optional parameter, this is the time in ms per channel. 

 

For example,   “scan 30” reduces the total scan time down to about 1 
second.   This command also works in Adhoc mode.  If the optional 

P

 

parameter is entered, the module will perform a passive scan, and list all 
APs that are seen in passive mode. 

 

sleep 

Puts the module to sleep mode. The module can come out of sleep mode 
by either sending characters over the uart or by using the wake timer. 

 

time 

Sets the Real time clock by synchronizing with the time server specified 
with the time server parameters  (see section 5.9)  This command sends a 
UDP time server request packet. 

 

9.

 

File IO Commands 

 

del<name><num> 

Deletes a file.  Optional <num> will override the name and use the sector 
number shown in the “ls” command. 

 

load  <name>

 

Reads in a new config file. 

 

ls 

Displays the files in the system

 

 

save

 

Saves the configuration to “config” (the default file). 

 

save  <name>

 

Saves the configuration data to a new file name 

 

boot image <num>

 

Makes file <num> the new boot image. 

 

Summary of Contents for RN-171








































































Reviews:

No comments

Brands by name

Popular brands

Load more brands