background image

E-M-HP22-V1_21 

Rotronic AG 
Bassersdorf, Switzerland 

Document code 

Unit 

HygroPalm HP22 hand-held indicator: 

User Guide 

Instruction Manual 

Document Type 

Page 

8

 of 16 

Document title 

 
 

© 2009-2010; Rotronic AG                                                                                                                             E-M-HP22-V1_21

 

4  

Operation 

4.1    Display 

 
The LC display of the HP22 has a backlight which 
can be set to be on all the time or whenever a key is 
pressed. The backlight can also be disabled. 
 
The upper line corresponds to relative humidity or 
dew / frost point and the bottom line corresponds to 
temperature.

 

 
The display can be configured to show a trend 
indicator on each line: 
 
▲: increasing value 
▼: decreasing value 
 

 
In the event of an alarm the display shows the symbol 

[ ! ] 

to the right of the value. 

 
For instructions see the following HW4 manual: 

E-M-HW4v2-F2-006

 

4.2    Keypad 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

 ON/OFF: 

Turns the instrument on or off 

MENU: 

Press this key to activate the 
internal menu. Press this key 
again to exit the menu

 

UP / DOWN: 

When the menu is active, use these 
keys to navigate the menu, make a 
selection or change a value 

ENTER: 

When the menu is active, press                          
this key to confirm a selection. 

Summary of Contents for HygroPalm HP22

















Reviews: