6
RCD-06 SE Stereo Compact Disc Player
Getting Started
Thank you for purchasing the Rotel RCD-06 SE Stereo Compact Disc
Player. Its precision transport is back up by a high performance Wolfson
D/A converter. These features, combined with Rotel’s Balanced Design,
ensure the RCD-06 SE will deliver the highest level of audio performance.
When used in a high-quality audio system, your Rotel CD player will
provide years of enjoyment.
A Few Precautions
Please read this manual carefully.In addition to installation and operating
instructions, it provides valuable information on various RCD-06 SE system
configurations as well as general information that will help you get
optimum performance from your system. Please contact your authorized
Rotel dealer for answers to any quesions you might have. In addition,
all of us at Rotel welcome your questions and comments.
Save the RCD06 SE shipping carton and all enclosed packing material
for future use. Shipping or moving the RCD-06 SE in anything other than
the original packing material may result in severe damage that is not
covered by the warranty.
Fill out and send in the owner’s registration card packed with the
RCD-06 SE. Also be sure to keep the original sales receipt. It is your
best record of the date of purchase, which you will need in the event
warranty service is required.
Placement
Use common sense when placing the RCD-06 SE in a cabinet or when
stacking other equipment. Make sure that the shelf or cabinet can support
its weight. Do not stack heavy components on top of the RCD-06 SE.
Avoid placing the unit where it may be subject to excessive heat such
as on top of a large power amplifier or near a heat register. For best
performance, avoid placing the unit where it may be subject to vibration,
such as near a speaker.
Control Identification
This manual shows illustrations of the front and rear panels and the RR-
D95 remote control. Each item in the illustrations is identified with a call
out in a gray box. Through out this manual the items refered to in the
text are identified by the corresponding call out. The items on the front
and rear panels are identified with a number call out, such a
1
. The
items on the remote control are labeled with a letter call out, such as
A
.
AC Power and Control
AC Power Input
e
Your RCD-06 SE is configured at the factory for the proper AC voltage in
the country where you purchased it (either 120 volts or 230 volts). The
AC line configuration is noted on a decal on the back panel.
Note:
Should you move your CD player to another country, it may be
possible to reconfigure it for use on a different line voltage. Do not attempt
to perform this conversion yourself. Opening the enclosure of the RCD-06
SE exposes you to dangerous voltages. Consult a qualified service person
or the Rotel factory service department for information.
The RCD-06 SE should be plugged directly into a 2-pin polarized wall
outlet or into the switched outlet on another component in your audio
system. Do not use an extension cord.
Be sure the power switch on the front panel of the RCD-06 SE is turned
off (in the “out” position). Then, connect the supplied power cord to the
AC power receptacle on the rear of the unit and the AC power outlet.
If you are going to be away from home for an extended period of time
such as a month-long vacation, it is a sensible precaution to unplug
your CD player (as well as other audio and video components) while
you are away.
Power Switch
1
and POWER Indicator
2
The power switch is located on the front panel of your CD player. To
turn the CD player on, push the switch in. The LED indicator above the
switch and the Display will light up, indicating that the CD player is
turned on. To turn the CD player off, push the button again and return
it to the “out” position.
Note:
If you are using a switched outlet to turn on and off your CD player,
you should leave the power switch in the “on” position. When AC power
is applied to the unit, it will power up in fully active mode.
Output Connections
The RCD-06 SE gives you a choice of two different kinds of output
connections—an analog output signal from the built-in D/A converter
for use with conventional analog audio components and a coax digital
output which provides an unprocessed digital data signal for use with
outboard D/A converters or digital processors.
Note:
To prevent loud noises that neither you nor your speakers will
appreciate, make sure the CD player is turned off when you make any
signal connections.
Analog Outputs
-
[
See Figure 3 for wiring illustration
]
A pair of standard RCA jacks supplies an analog output signal from
the RCD-06 SE to the source inputs of an audio preamplifier,integrated
amplifier, or receiver.
Select high quality audio interconnect cables. Connect the left channel
output of the RCD-06 SE to the left channel source input on the pream-
plifier or other component. Connect the right output of the RCD-06 SE to
the right channel source input on the preamplifier or other component.
Digital Output
=
[
See Figure 4 for wiring illustration
]
If you are using an outboard D/A converter or other digital processor,
you will need an unprocessed digital data stream from the RCD-06 SE,
taken before the built-in D/A converter. This signal is supplied by The
RCD-06 SE’s backpanel digital output jack. Using a standard 75 ohm
coax digital cable, connect the RCD-06 SE’s coax digital output to the
coax digital input connector on the outboard D/A converter.
