Ross QRA-8808 User Manual Download Page 27

Page: 27 / 32

QRA-8808 User Guide (v5.0)

Technical Specifications • 27

Technical Specifications

This chapter includes the technical specifications for the QRA-8808.



Specifications are subject to change without notice.

Supported Rear Modules

• 8320AR-302

SDI Inputs Specifications

SDI Outputs Specifications

Table 9.1 Technical Specifications — SDI Inputs

Item

Specifications

Standards Accommodated

19.39Mbps, 38.78Mbps, SMPTE 310

270Mbps, 525/625 Component, SMPTE 259M

270Mbps, DVB-ASI

1.485Gbps Component, SMPTE 292M

2.97Gbps Component, SMPTE 424M

Impedance



terminating

Equalization (Belden 1694A Cable)

Channel A, Channel B

>500m (1640ft) @ 270MBps
>200m (650ft) @ 1.485GBps
>120m (394ft) @ 2.97GBps

Channel C, Channel D

>500m (1640ft) @ 270MBps
>150m (492ft) @ 1.485GBps
>110m (360ft) @ 2.97GBps

Return Loss

>15dB to 3GHz

Connector Type

HD-BNC

Table 9.2 Technical Specifications — SDI Outputs

Item

Specifications

Impedance



Return Loss

>15dB to 1.485GHz

>10dB to 2.97GHz

Signal Level

800mV ±10%

DC Offset

0V ±50mV

Rise & Fall Time (20-80%)

700ps typical (270Mbps)

120ps typical (1.485Gbps)

135ps typical (2.97Gbps)

Summary of Contents for QRA-8808

































Search results

Summary of Contents for QRA-8808

Reviews:

Related manuals for QRA-8808

Brands by name

Popular brands

Ross QRA-8808, User Manual

Search results

Summary of Contents for QRA-8808

Reviews:

Related manuals for QRA-8808

Brands by name

Popular brands