Ross DRA-8604 User Manual Download Page 9 | Manualshive

Page: 9 / 44

background image

DRA-8604 User Manual (Iss. 02)

Introduction • 1–1

Introduction

In This Chapter

This chapter contains the following sections:

• Overview
• Functional Block Diagrams
• User Interfaces
• Documentation Terms and Conventions

A Word of Thanks

Congratulations on choosing an openGear DRA-8604 Dual 3G/HD/SD Reclocking Amplifier.
Your DRA-8604 is part of a full line of products within the openGear Terminal Equipment family
of products, backed by Ross Video’s experience in engineering and design expertise since 1974.

You will be pleased at how easily your new card fits into your overall working environment.
Equally pleasing is the product quality, reliability and functionality. Thank you for joining the
group of worldwide satisfied Ross Video customers!

Should you have a question pertaining to the installation or operation of your card, please contact
us at the numbers listed on the back cover of this manual. Our technical support staff is always
available for consultation, training, or service.

«
...
7
8
9
10
11
...
»

Summary of Contents for DRA-8604













































Reviews:

No comments

Related manuals for DRA-8604

Brand: Sponsler Pages: 4

Brand: Gibson Pages: 1

Brand: Interface Devices Pages: 8

Brand: Miranda Pages: 4

Brand: J&M Corporation Pages: 4

D:CORE STEREO 10

Brand: Blackstar Pages: 10

Brand: Skytec Pages: 26

Brand: Target Audio Pages: 16

Brand: BMC Pages: 20

Brand: Xtant Pages: 2

Brand: Warmenfat Pages: 12

Brand: GLEMM Pages: 12

Brand: PrimaLuna Pages: 8

FUSION SIGNATURE Series

Brand: Garmin Pages: 18

Brand: Art Pages: 16

Brand: Destination Audio Pages: 12

Brand: PowerBass Pages: 28

Brand: Fender Pages: 23

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands