Ross DRA-8604 User Manual Download Page 16 | Manualshive

Page: 16 / 44

background image

2–2 • Installation

DRA-8604 User Manual (Iss. 02)

Before You Begin

Before proceeding with the instructions in this chapter, ensure that your openGear frame is
properly installed according to the instructions in the

DFR-8300 and OG3-FR Series User

Manual

.

Static Discharge

Throughout this chapter, please heed the following cautionary note:

Unpacking

Unpack each card you received from the shipping container and ensure that all items are included.
If any items are missing or damaged, contact your sales representative or Ross Video directly.

ESD Susceptibility

— Static discharge can cause serious damage to sensitive

semiconductor devices. Avoid handling circuit boards in high static environments such as
carpeted areas and when synthetic fiber clothing is worn. Always exercise proper grounding
precautions when working on circuit boards and related equipment.

«
...
14
15
16
17
18
...
»

Summary of Contents for DRA-8604













































Reviews:

No comments

Related manuals for DRA-8604

Brand: Randall Pages: 9

Brand: rabbitone Pages: 2

Brand: Gibson Pages: 1

Brand: Interface Devices Pages: 8

Brand: Jedia Pages: 16

Brand: National Instruments Pages: 14

Brand: Radio Shack Pages: 24

Brand: Ericsson Pages: 34

Brand: Uniden Pages: 2

Brand: TC Electronic Pages: 24

Brand: PSSO Pages: 28

Brand: Harley Benton Pages: 2

Road Thunder RT1000-1D

Brand: MTX Pages: 48

Brand: Inter-m Pages: 8

Brand: Radio Shack Pages: 4

V30 The Countess

Brand: Victory Pages: 8

Velocity VD 1002

Brand: Blaupunkt Pages: 22

Brand: Somogyi Elektronic Pages: 20

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands