Ross DRA-8604 User Manual Download Page 2 | Manualshive

Page: 2 / 44

background image

DRA-8604 User Manual

• Ross Part Number: 8604DR-004-02
• Release Date: July 25, 2013.

The information in this manual is subject to change without notice or obligation.

Copyright

© 2013 Ross Video Limited

. All rights reserved.

This work is proprietary and confidential to Ross Video Limited, its subsidiaries and its other
affiliated corporations and may not be copied, distributed, sold or otherwise used or relied upon
without the express written permission of Ross Video Limited. Reproduction or reverse
engineering of copyrighted software is prohibited.

Patents

This product is protected by the following US Patents: 4,205,346; 5,115,314; 5,280,346;
5,561,404; 7,304,886; 7,508,455; 7,602,446; 7,834,886; 7,914,332. This product is protected by
the following Canadian Patents: 2039277; 1237518; 1127289. Other patents pending.

Notice

The material in this manual is furnished for informational use only. It is subject to change without
notice and should not be construed as commitment by Ross Video Limited. Ross Video Limited
assumes no responsibility or liability for errors or inaccuracies that may appear in this manual.

Trademarks

•

is a registered trademark of Ross Video Limited.

• Ross, ROSS, ROSS®, and MLE are registered trademarks of Ross Video Limited.
• openGear® is a registered trademark of Ross Video Limited.
• DashBoard Control System™ is a trademark of Ross Video Limited.
• All other product names and any registered and unregistered trademarks mentioned in

this manual are used for identification purposes only and remain the exclusive property of
their respective owners.

«
1
2
3
4
...
»

Summary of Contents for DRA-8604













































Reviews:

No comments

Related manuals for DRA-8604

Brand: Hama Pages: 8

Brand: Aaron Pages: 2

Brand: D.A.S. Pages: 15

Brand: Advance acoustic Pages: 18

Brand: Atlona Pages: 10

Brand: Arcam Pages: 18

Brand: KODA Pages: 35

a-1 C.R.I.S.T.A.L. AUDIOPHILE

Brand: Definity Audio Pages: 13

Brand: Kustom Pages: 12

Brand: Rane Pages: 6

Brand: Linear Technology Pages: 9

Brand: Optimus Pages: 14

Brand: Rotel Pages: 16

Brand: Perreaux Pages: 2

Series VII Aphrodite

Brand: Hifonics Pages: 58

Brand: Kramer Pages: 12

Brand: IRT Electronics Pages: 10

Brand: Kramer Pages: 13

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands