manualshive.com logo in svg

Rosemount 485 Annubar, Quick Installation Manual

Share
Download
Rosemount 485 Annubar Quick Installation Manual Download Page 2

Quick Installation Guide

00825-0100-4809, Rev DB

December 2009

Flanged 485 Annubar 

2

©  2009 Rosemount Inc. All rights reserved. All marks property of owner. Rosemount and the Rosemount logotype are 

registered trademarks of Rosemount Inc. 

Rosemount Inc.

8200 Market Boulevard

Chanhassen, MN USA 55317

T (US) (800) 999-9307

T (Intnl) (952) 906-8888

F (952) 949-7001

Emerson Process Management GmbH & Co. OHG

Argelsrieder Feld 3

82234 Wessling

Germany

T 49 (8153) 9390

F49 (8153) 939172

Emerson Process Management Asia Pacific 
Private Limited

1 Pandan Crescent

Singapore 128461

T (65) 6777 8211

F (65) 6777 0947/65 6777 0743

Beijing Rosemount Far East Instrument Co., 
Limited

No. 6 North Street, 

Hepingli, Dong Cheng District

Beijing 100013, China

T (86) (10) 6428 2233

F (86) (10) 6422 8586

IMPORTANT NOTICE

This installation guide provides basic guidelines for Rosemount

485 Annubar. It does not provide instructions for configuration, diagnostics, maintenance, 

service, troubleshooting, Explosion-proof, Flameproof, or Intrinsically Safe (I.S.) 

installations. Refer to the 485 Annubar reference manual (document number 

00809-0100-4810) for more instruction. This manual is also available electronically on 

www.rosemount.com.

If the 485 Annubar was ordered assembled to a Rosemount 3051S transmitter, see the 

following Quick Installation Guide for information on configuration and hazardous 

locations certifications: Rosemount 3051S Series Pressure Transmitter (document 

number 00825-0100-4801).

If the 485 Annubar was ordered assembled to a Rosemount 3095 transmitter, see the 

following Quick Installation Guide for information on configuration and hazardous 

locations certifications: Rosemount 3095 (document number 00825-0100-4716).

WARNING

Process leaks may cause harm or result in death. To avoid process leaks, only use 

gaskets designed to seal with the corresponding flange and o-rings to seal process 

connections. Flowing medium may cause the 485 Annubar assembly to become hot and 

could result in burns.

CAUTION

If pipe/duct wall is less than 0.125-in. (3,2 mm) use extreme caution when installing 

sensor. Thin walls can deform during welding, installation or from the weight of a 

cantilevered flowmeter. These installations may require a fabricated outlet, saddle or 

external flowmeter support. Please consult factory for assistance.

0100-4809 Rev DB.fm  Page 2  Wednesday, December 30, 2009  3:57 PM

Summary of Contents for 485 Annubar

















Reviews:

No comments

Brands by name

Popular brands

Load more brands