manualshive.com logo in svg

Rosemount 485 Annubar, Quick Installation Manual

Share
Download
Rosemount 485 Annubar Quick Installation Manual Download Page 15

Quick Installation Guide

00825-0100-4809, Rev DB

December 2009

Flanged 485 Annubar

15

P

RODUCT

 C

ERTIFICATIONS

Approved Manufacturing Locations

Rosemount Inc. — Chanhassen, Minnesota  USA

European Directive Information

The EC declaration of conformity for all applicable European directives for this product can 

be found on the Rosemount website at www.rosemount.com. A hard copy may be obtained 

by contacting our local sales office.

European Pressure Equipment Directive (PED) (97/23/EC)

Rosemount 485 Annubar — Refer to EC declaration of conformity for conformity 

assessment

Pressure Transmitter — See appropriate Pressure Transmitter QIG

Hazardous Locations Certifications

For information regarding the transmitter product certification, see the appropriate 

transmitter QIG:

• Rosemount 3051S (document number 00825-0100-4801)

• Rosemount 3095M (document number 00825-0100-4716)

0100-4809 Rev DB.fm  Page 15  Wednesday, December 30, 2009  3:57 PM

Summary of Contents for 485 Annubar

















Reviews:

No comments

Brands by name

Popular brands

Load more brands