38
TF 200.01.0047_eng
5. Performance test
After completed installation and before use, all functions of the Ropox Support Washbasin must be tested.
After that, a performance test must be carried out at least once a year by competent personnel.
1.
Check that the mounting instructions have been observed.
2.
Check that all bolts and screws have been tightened.
3.
Check that all drains and hoses have been correctly connected.
4.
Ensure that there is no load on the frame.
5.
Ensure that there are no objects preventing the frame from moving freely within the height
adjustment range.
When these tests have been carried out successfully, Ropox Support Washbasin is ready for use. See
Section
”Safety in use”.
6. Safety in use
➢
Ropox Support Washbasin must only be adjusted in height by persons who have read and
understood these instructions.
➢
Some models of Ropox Support Washbasin are height-adjustable and must not be used as a lifting
table or person lifter.
➢
Always use the washbasin in a manner excluding the risk of damage to persons or property. The
person operating the washbasin is responsible for avoiding damage or injury.
➢
If the washbasin is used in publicly accessible locations where children or persons with reduced
observation capacity may get near it, the person operating the washbasin must pay attention to
those present in order to prevent dangerous situations.
➢
Make sure that there is free space above and below the washbasin to allow height adjustment.
➢
Do not overload Ropox Support Washbasin and make sure that the load distribution is correct.
➢
Do not operate the washbasin in case of defects or damage.
➢
Modifications, which may influence the performance or design of Ropox Support Washbasin, are not
allowed.
➢
Be aware that the washbasin becomes slippery when wet.
➢
Be aware that if there is water in the washbasin when it is height adjusted, it may spray on the floor.
➢
Be aware that if the drain stops when the water is running, the floor will get wet.
➢
Installation, service and repairs must be carried out by competent personnel.
➢
During inspection, service or repairs any load must be removed from Ropox Support Washbasin.
Summary of Contents for 40-44010
