background image

CORDLESS DRIVER DRILL

16

IMPORTANT CHARGING NOTES

1. The charger was designed to fast charge the battery only when the 
battery temperature is between 32F (0C) and 113F (45C). If the battery 
pack is too hot or too cold, the charger will not fast charge the battery. 
(this may happen if the battery pack is hot from heavy use). When the 
battery temperature returns to between 32F (0C) and 113F (45C), the 
charger will automatically begin charging.
2. A substantial drop in operating time per charge may mean that the 
battery pack is nearing the end of its life and should be replaced.
3. Remember to unplug charger during storage period.
4. If battery does not charge properly:
a. Check for voltage at outlet by plugging in some other electrical device.
b. Check to see if outlet is connected to a light switch which turns power 
“off” when lights are turned off.
c. Check battery pack terminals for dirt. Clean with cotton swab and 
alcohol if necessary.
d. If you still do not get proper charging, take or send tool, battery pack 
and charger to your local Bosch service Center. See “Tools, Electric” in 
the Yellow Pages for names and addresses.
Note: use of chargers or battery packs not sold by Bosch will void the warranty.

CHARGER INDICATORS, SYMBOLS AND MEANING

If the indicator light are “OFF”, charger is not receiving power from power 
supply outlet.
If the green indicator light is “ON”, the charger is plugged in but the battery 
pack is not inserted, or the battery pack is fully charged and is being 
trickle charged.
If the green indicator light is “BLINKING”, the battery pack is being fast-charged. 
Fast charging will automatically stop when the battery pack is fully charged. 
If the red indicator light is “ON” the battery pack is too hot or cold for 
fast-charging. The charger will switch to trickle charge, until a suitable 

Summary of Contents for 8512





















Reviews: