eng eng
NOTICE
NOTICE
Charge the battery before use. Recharge Li-Ion batteries regularly to avoid
their total discharge. The rechargeable battery will be damaged by total
discharge.
Only use approved ROLLER’S rapid chargers for charging the ROLLER’S
battery, see Guidelines for use, fi g. 4. New Li-Ion batteries and Li-Ion batteries
which have not been used for a long time only reach full capacity after several
charges.
Rapid charger (accessory, Art. No. 571560)
The left control lamp lights up and remains green when the mains plug is
plugged in. If a battery is inserted in the rapid charger, the green control lamp
fl ashes to indicate that the battery is charging. The green light stops fl ashing
and remains on to signal that the battery is fully charged. If the red control lamp
fl ashes, the battery is defective. If the red control lamp comes on and remains
on, this indicates that the temperature of the rapid charger is outside the permis-
sible range of 0°C to +45°C.
NOTICE
NOTICE
The rapid chargers are not suitable for outdoor use.
2.2. Installing the Machine
Place the electric pipe cutting machine on a ROLLER’S Werkmeister E or
ROLLER’S Werkmeister collapsible workbench (accessory, Art. No. 120240 or
120200). Alternatively, unscrew the pipe arm (2) and clamp the basic body (1)
in the vice (Fig. 3) or bolt the basic body to a form base with screws through
the holes (3). Longer pipes must be supported on both sides of the machine if
necessary with ROLLER’S Assistent 3B or ROLLER’S Assistent WB (accessory,
Art. No. 120120 or 120130).
2.3. Fitting (Changing) the Cutting Wheel (4)
Pull out the mains plug or remove the battery! Choose suitable cutting wheel:
●
ROLLER cutting wheel Cu-INOX for stainless steel pipes, steel pipes and
copper pipes of the pressfi tting systems
●
ROLLER cutting wheel V for composite pipes.
Remove hexagon nut (5) with single open-ended wrench size 8. Insert (change)
cutting wheel (4). Make sure that the cams of the drive shaft engage in the
drivers of the cutting wheel. Replace the hexagon nut (5)
NOTICE
NOTICE
Use only an original ROLLER cutting wheels! An unsuitable cutting wheel will
be damaged or the pipe will not be cut.
3. Operation
CAUTION
CAUTION
Danger of injury!
Wear suitable clothing. Do not wear loose clothing or jewellery. Keep hair,
clothing and gloves away from moving parts. Loose clothing, jewellery or
long hair can get caught in moving parts.
3.1. Work procedure
Pull up the handle (7) until the pipe to be cut can be placed on the pipe rest
(6). Outside burr (sawing burr) must be removed from the pipe otherwise the
rollers will be damaged. Make sure that the a cutting wheel (4) suitable for the
pipe to be cut is selected/fi tted. Do not allow the pipe to knock against the
cutting wheel when inserting, the cutting wheel could be damaged. Mark the
cutting point on the pipe and position it to the cutting wheel. Support longer
pipes (see 3.2). Press the safety inching switch (8), press the handle (7) against
the pipe rest and cut the pipe.
NOTICE
NOTICE
If the cutting wheel breaks during cutting, the same cutting notch in the pipe to
be cut may not be used after changing the cutting wheel. The changed cutting
wheel will be damaged by fragments left in the cutting notch.
3.2. Supporting the Material
CAUTION
CAUTION
Always support pipes and longer pipe sections, on both sides if necessary, e.g.
with height-adjustable ROLLER’S Assistent 3B or ROLLER’S Assistent WB
material rests (accessory, Art. No. 120120 or 120130). Make sure that the
height-adjustable material rest is set to the same height of the pipe rest (6).
This reduces untrue running and uncontrolled falling of the pipe to the ground.
3.3. Low Discharge Protection
ROLLER’S
Smart-Cut 11 V is equipped with low discharge protection for the
Smart-Cut 11 V
Smart-Cut 11 V
battery. This switches off the power tool as soon as the battery needs to be
recharged. In this case remove the battery and charge with the ROLLER rapid
charger.
4. Maintenance
Notwithstanding the maintenance described below, it is recommended to send
in the power tool to an authorised ROLLER contract customer service workshop
for inspection and periodic testing of electrical devices at least once a year. In
Germany, such periodic testing of electrical devices should be performed in
accordance with DIN VDE 0701-0702 and also prescribed for mobile electrical
equipment according to the accident prevention rules DGUV, regulation 3
"Electrical Systems and Equipment". In addition, the respective national safety
provisions, rules and regulations valid for the application site must be considered
and observed.
4.1. Servicing
WARNING
WARNING
Pull out the mains plug or remove the battery before maintenance work!
Keep the rollers of the pipe rest (6), cutting wheel (4) and cutting wheel holder
clean. Clean heavily soiled metal parts with machine cleaner and then protect
against rust.
Clean plastic parts (e.g. housing) only with machine cleaner or a mild soap and
a damp cloth. Do not use household cleaners. These often contain chemicals
which can damage the plastic parts. Never use petrol, turpentine, thinner or
similar products for cleaning.
Make sure that liquids never get onto or inside the power tool. Never immerse
the power tool in liquid.
4.2. Inspection/Repair
WARNING
WARNING
Before any repair work, pull the mains plug or remove the battery! This
Before any repair work, pull the mains plug or remove the battery!
Before any repair work, pull the mains plug or remove the battery!
work may only be performed by qualifi ed personnel.
The gear ROLLER’S Smart-Cut, ROLLER’S Smart-Cut 11 V runs in a life-long
Smart-Cut 11 V
Smart-Cut 11 V
grease fi lling and therefore needs no lubrication. The motors of ROLLER’S
Smart-Cut and ROLLER’S Smart-Cut 11 V have carbon brushes. These are
Smart-Cut 11 V
Smart-Cut 11 V
subject to wear and must therefore be checked by qualifi ed specialists or an
authorised ROLLER customer service workshop from time to time. The carbon
brushes cannot be replaced so that the motor may have to be changed. See
also page 5. Behaviour in the event of faults
5. Behaviour in the event of faults
5.1. Fault: Electric pipe cutting machine, cordless pipe cutting machine comes to a standstill during cutting.
Cause:
Remedy:
● Feeding pressure too high.
● Reduce feeding pressure.
● Blunt/broken cutting wheel.
● Change cutting wheel.
● Worn carbon brushes.
● Have the motor changed by an authorised ROLLER customer service
workshop.
● Battery fl at or defective (ROLLER’S Smart-Cut 11 V).
Smart-Cut 11 V
Smart-Cut 11 V
● Charge the battery with the rapid charger or change the battery.
e r
e r
5.2. Fault: Pipe stops during cutting.
Cause:
Remedy:
● Pipe not round.
● Reduce feeding pressure.
● Pipe not deburred on the outside.
● Deburr pipe on outside.
● Rollers of the pipe rest (6) soiled.
● Clean rollers, see 4.1.
5.3. Fault: Pipe is not cut.
Cause:
Remedy:
● Unsuitable cutting wheel.
● Select and change cutting wheel according to the pipe to be cut.
● Pipe not round.
● Reduce feeding pressure.
● Pipe not deburred on the outside.
● Deburr pipe on outside.
● Cutting wheel damaged.
● Change cutting wheel.
10
