background image

Instrucciones de seguridad elementales 

1171.0000.42 - 08 

Page 13 

Reparación y mantenimiento 

1.  El producto solamente debe ser abierto por personal especializado con autorización para ello. Antes 

de manipular el producto o abrirlo, es obligatorio desconectarlo de la tensión de alimentación, para 
evitar toda posibilidad de choque eléctrico.  

2.  El ajuste, el cambio de partes, el mantenimiento y la reparación deberán ser efectuadas solamente 

por electricistas autorizados por Rohde & Schwarz. Si se reponen partes con importancia para los 
aspectos de seguridad (p. ej. el enchufe, los transformadores o los fusibles), solamente podrán ser 
sustituidos por partes originales. Después de cada cambio de partes relevantes para la seguridad 
deberá realizarse un control de seguridad (control a primera vista, control del conductor de 
protección, medición de resistencia de aislamiento, medición de la corriente de fuga, control de 
funcionamiento). Con esto queda garantizada la seguridad del producto.  

Baterías y acumuladores o celdas 

Si no se siguen (o se siguen de modo insuficiente) las indicaciones en cuanto a las baterías y 
acumuladores o celdas, pueden producirse explosiones, incendios y/o lesiones graves con posible 
consecuencia de muerte. El manejo de baterías y acumuladores con electrolitos alcalinos (p. ej. celdas de 
litio) debe seguir el estándar EN 62133.

 

1.  No deben desmontarse, abrirse ni triturarse las celdas.  

2.  Las celdas o baterías no deben someterse a calor ni fuego. Debe evitarse el almacenamiento a la luz 

directa del sol. Las celdas y baterías deben mantenerse limpias y secas. Limpiar las conexiones 
sucias con un paño seco y limpio. 

3.  Las celdas o baterías no deben cortocircuitarse. Es peligroso almacenar las celdas o baterías en 

estuches o cajones en cuyo interior puedan cortocircuitarse por contacto recíproco o por contacto con 
otros materiales conductores. No deben extraerse las celdas o baterías de sus embalajes originales 
hasta el momento en que vayan a utilizarse. 

4.  Las celdas o baterías no deben someterse a impactos mecánicos fuertes indebidos. 

5.  En caso de falta de estanqueidad de una celda, el líquido vertido no debe entrar en contacto con la 

piel ni los ojos. Si se produce contacto, lavar con agua abundante la zona afectada y avisar a un 
médico. 

6.  En caso de cambio o recarga inadecuados, las celdas o baterías que contienen electrolitos alcalinos 

(p. ej. las celdas de litio) pueden explotar. Para garantizar la seguridad del producto, las celdas o 
baterías solo deben ser sustituidas por el tipo Rohde & Schwarz correspondiente (ver lista de 
recambios).  

7.  Las baterías y celdas deben reciclarse y no deben tirarse a la basura doméstica. Las baterías o 

acumuladores que contienen plomo, mercurio o cadmio deben tratarse como residuos especiales. 
Respete en esta relación las normas nacionales de eliminación y reciclaje.  

Transporte 

1.  El producto puede tener un peso elevado. Por eso es necesario desplazarlo o transportarlo con 

precaución y, si es necesario, usando un sistema de elevación adecuado (p. ej. una carretilla 
elevadora), a fin de evitar lesiones en la espalda u otros daños personales.  

Summary of Contents for TS-PSU12































































Reviews: