Rohde & Schwarz 4091.7009.02 Getting Started Download | Manualshive

Page: 46 / 61

background image

Software and Firmware Update

R&S

®

EB510

46

Getting Started 4091.7338.02 ─ 01

show more than one installer image. Use the ROTARY KNOB to select an image
and press ENT.

Version of Updater Program

Make sure that the version of the updater program is the same or higher than
the version of the firmware image you want to install. The version of the
updater program is shown in the dialog title of the first dialog.
If for some reason the version of the R&S

EB510 updater program is lower

than the firmware you want to install (e.g. because you installed an older ver-
sion of the firmware), just copy again the update installation file to the USB
flash drive, following the steps explained in

chapter 4.2.1, "Prepara-

, on page 41. This will overwrite the original updater program so that

both the firmware and the updater program have the same version on the USB
flash drive.

One image will contain an updated version of the receiver firmware as well as the
GUI. The receiver firmware will be updated first. The firmware will be copied from
USB flash drive to EEPROM on the processor board. The EEPROM needs to be
erased first, after which the program code will be downloaded and the checksum
calculated.

Receiver Firmware and GUI Update for EB510 with front control panel

«
...
44
45
46
47
48
...
»

Summary of Contents for 4091.7009.02






























































Reviews:

No comments

Related manuals for 4091.7009.02

Brand: Parallel Audio Pages: 8

DENON AVR-X4000W

Brand: D+M Group Pages: 21

Brand: FTE Maximal Pages: 44

Brand: OEM Pages: 58

IC-F3260 Series

Brand: Icom Pages: 40

Brand: Sirius Satellite Radio Pages: 36

Brand: Covid Pages: 11

Brand: Harman Kardon Pages: 8

Brand: Skymaster Pages: 28

Brand: Aiwa Pages: 33

Brand: XY-AUTO Pages: 23

Brand: Kia Pages: 26

Raymarine AIS5000

Brand: FLIR Pages: 110

Brand: Grundig Pages: 42

Brand: Matsui Pages: 2

Brand: GAMA Electronics Pages: 5

Brand: CryptoBox Pages: 48

Brand: Icom Pages: 71

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands