background image

WWW.GAMAINC.COM

Included in this Kit:
(1) RFAC-1L Receiver
(1) 2-Button Transmitter 

*Image shown with standard transmitter*

- Long Range Antenna LRA340A 

**SEE PAGE 3 FOR SETUP**

Available accessories:
- Additional Transmitter KF340-2 
- Waterproof Transmitter KF340-2WP
- Rechargeable Transmitter GKF-WPTX-2
- 6-Pack of Replacement A-23 12V Batteries A23-6

The RFAC-1L is a RF receiver operating at a fixed frequency of 340 MHz. The receiver operates from 120VAC to 240VAC 
input power and provides one AC output at the input voltage. The receiver operates with Model KF340-2 transmitter. Up to 
30 transmitters can be stored in the receiver’s memory, and are programmed into the receiver’s memory during the 
programming process. A manual On/Off button will operate the control without the need for a remote control. The On/Off 
button is also used to program remote controls to the receiver. An LED on the On/Off switch indicates the receiver's 
programming status and illuminates when the relay is energized. The receiver is encased in a small, waterproof 
enclosure. The receiver provides two wires for input power and two wires for output power. The unit operates a single 
latching output. The relay will toggle on and off each time a switch is pressed on the transmitter. 

Operating Temperature Range:

 0°F to 160°F

Waterproof Rating: 

IP67

Maximum Ratings: 

Power for the receiver can be in the range of 100-250VAC. The output is rated at 1HP 20A @ 

120VAC and 1 1/2 HP 20A @ 240VAC. 

Input/output Connections: 

100-250VAC input power connects to the Black (line) and White (Neutral) wires. Output 

power, identical to the input power, connects to the Blue (line) and Yellow (neutral) wires.

Dimensions:

 Receiver dimensions are 4.00"W x 2.00”D x 3.67"H. 

Page 1 REV O 09/10/20

RFAC-1L

Instruction Manual

Summary of Contents for RFAC-1L






Reviews: