PRT-EM Series Readers fv 1.29 and 2.29 Rev. J.doc
2012-01-05
Page 13 from 59
5 .
S
T A N D A L O N E
M
O D E
5.1.
U
SERS
When operating in standalone mode, the PRT-EM reader can register up to 120 users, each with a
card and/or PIN (3-6 digits). Entry of a PIN code must be followed by the [#] which is required to
mark the end of the PIN. Users can be identified by their PIN-s or cards. When the
Card and PIN
option
is active, user must first present card and then subsequently enter PIN. The
Identification
Mode
can be set individually for primary and secondary reader.
Note: In standalone mode reader uses full card code (40 bits).
The PRT-EM reader supports five types (classes) of users:
MASTER
INSTALLER
NORMAL
TOGGLE
TOGGLE LTD
Types of Users
Type
ID
Authorisation
Programming
MASTER
None
This user is allowed to enter
User Programming
mode and can have card and/or PIN.
Memory Reset
and User
Programming
INSTALLER None
This user is allowed to enter
Installer Programming
mode only and can have card and/or PIN.
Memory Reset
and User
Programming
NORMAL
0-119
NORMAL users are solely authorized to unlock the
controlled door, they can have card and/or PIN.
User
Programming
TOGGLE
0-119
TOGGLE users are authorized to unlock the controlled
door and to switch reader between armed and
disarmed mode, they can have card and/or PIN.
User
Programming
TOGGLE
LTD
0-199
TOGGLE LTD (TOGGLE LIMITED) are solely authorized
to switch reader between armed and disarmed modes,
they can have card and/or PIN.
User
Programming
Note: All users can be programmed from RARC program as well.
Note: The MASTER and INSTALLER card can be used as so called
Programming Cards
when
employing programming method of
multiple readings
of proximity card (for readers without
keypad).
5.1.1.
Managing the Users
A new user can be registered in the reader using either the
Simple Programming
or
Full
Programming
procedure.
The
Simple Programming
procedure consists of programming of a PIN and/or card without
specifying the ID number of a user to whom the programmed PIN/card will be assigned — as the
result reader simply stores the PIN/card in the first unoccupied user’s ID number.
The
Full Programming
procedure requires specifying of the ID number for the new user being
programmed which has to be followed by his PIN and/or card.
Note: When you program a user using the
Full Programming
procedure, later you will be able to
selectively delete or modify him by using his ID number. If you program card/PIN using the
Summary of Contents for PRT12EM
