background image

Version 2.0 

Copyright Roger™

-GPS 

2019 10 01 

12 

 

GNSS Technology Expert

  

 

 

ROGER™

-GPS 

Roger-GPS Ltd 
Finnoonniitynkuja 4 
02270 Espoo, Finland 

www.gps-repeating.com

 

 

WARRANTY 

Roger-GPS Ltd agrees that any hardware supplied under these Conditions shall be free from defects in materials and 
workmanship for a period of 24months from the date of the delivery "(the Warranty Period") covering material and 
workmanship. The 24 

months period is calculated from the date, the products are shipped from the Byer’s 

warehouse in the case that the Byer has an accounting system that keeps track on the shipment dates. 
Nevertheless, the warranty period cannot exceed in any circumstances 26 months from the date of delivery from 
Roger-GPS Ltd warehouse. 

Roger-GPS Ltd undertakes to remedy all defects in the Products notified to it by the Buyer during the Warranty 
Period by either repairing or replacing or refunding at Roger-

GPS Ltd.’s option the defective Product or defective 

part at Roger-

GPS Ltd.’s cost.

 

Goods returned under this guarantee shall be delivered to Roger™

-GPS Ltd at the B

uyer’s expense. Before shipping 

the products to Roger™

-GPS Ltd, the buyer must follow the instructions (

Roger-GPS

 

RMA procedure

) given by 

Roger™

-GPS Ltd and the inward processing directives set by the Finnish Customs.

 

Warranty will be void in respect of goods which in Roger-

GPS Ltd.’s reasonable opinion, have been subjected to 

unauthorised modification or repair, improper installation, neglect, misuse or operation in environmental 
conditions outside of specified safe operating extremes. The warranty applicable to non-

Roger™

-GPS Ltd product 

supplied by Roger™

-GPS Ltd shall be limited to the warranty terms offered by the manufacturer of the product. 

Roger-GPS Ltd shall not be liable to the Buyer for any consequential loss. 

No warranties, expressed or implied, including but not limited to, any implied warranty of merchantability of 
fitness for any purpose, are made or deemed to have been made by the Roger-GPS Ltd. 

Roger-GPS Ltd shall not be responsible to the Buyer or any other party in respect of any claims arising out of the 
sale of the products. Roger-GPS Ltd does not warrant the software delivered under these conditions per se but 
agrees to maintain the software for a period of 90 days from the date of delivery of the relevant software. 

The Buyer shall indemnify Roger-GPS Ltd against all proceedings, claims or demands in any way connected with the 
Conditions brought or threatened against Roger-GPS Ltd by a third party except to the extent that Roger-GPS Ltd is 
liable to the Buyer under the Conditions.

 

 

 
 
 
 

 

Supplier reserves all rights for product changes and upgrades. 

Pictures and texts are indicative

 

Summary of Contents for GNSS-L1G1GA-EU













Reviews: