Rockwell powerflex 700h Service Manual Download Page 80

Page: 80 / 120

3-34

Access Procedures

Removing the Left-Side
Output Power Module

Important:

Do not attempt to disassemble the Output Power Module.

Important:

Always replace the Output Power Modules in pairs (do not
replace just one module).

Remove power from the drive. Refer to

Removing Power from Drive on

page 3-3

Remove the covers from the power structure. Refer to

Removing the

Covers from the Power Structure on page 3-15

Remove the power structure from the drive cabinet. Refer to

Removing

the Power Structure from the Drive Enclosure on page 3-27

Remove the cable-tie that secures the Power Module circuit board to the
Adapter board.

Disconnect the output leads from the bottom of the Output Power
Module.

Remove the Y bus bars.

Y Bus Bars

Summary of Contents for powerflex 700h

























































































































Search results

Summary of Contents for powerflex 700h

Reviews:

Related manuals for powerflex 700h

Brands by name

Popular brands

Rockwell powerflex 700h, Service Manual

Search results

Summary of Contents for powerflex 700h

Reviews:

Related manuals for powerflex 700h

Brands by name

Popular brands